NJP-5500C Automatic Capsule Filling Machine — 330,000 Capsules/Hour
The NJP-5500C fills 330,000 capsules an hour. At this rate the constraint usually stops being the filler and becomes what feeds it and what takes capsules away — talk to us about the whole line, not just this machine.
1. Output: 330,000 capsules an hour
2. Dual 100DS Drive System: High-precision cam dividing boxes for high torque and low vibration at full speed.
3. Capsule-feeding success rate: 99.9% on empty capsules, 99.8% on filled. Unopened capsules are rejected automatically before they reach the dosing station.
4. Line integration: Ethernet/IP and Profinet connectivity for MES or SCADA. Tell us your protocol at the quotation stage.
Is the NJP-5500C the right filler for you?
✓ This is a fit if…
- You need around 330,000 capsules an hour as a sustained rate
- You run continuous high-volume production, with the blend upstream and the bottling downstream sized to keep up
- You're filling powder, granule or pellets
- You run 00# to 5# capsules
- Your room holds 21 °C ± 3 °C and 40–60% humidity
✕ Look elsewhere if…
- You need more than 330,000 an hour → the NJP-7500C runs 450,000 for a modest step up
- This is your only machine and you plan to scale within a year → buying the 7500C now costs less than buying the 5500C twice
- You're doing bench-scale R&D only → a semi-automatic filler costs a fraction of this
- Your powder is very fine and highly potent → an enclosed rotary machine with dust extraction is not the same as a contained or isolator system. Tell us your OEB band first
Technical specification
Model | NJP-5500C |
Max Output | 330,000 capsules/hour (5,500 pcs/min) |
Capsule Sizes | 00# to 5# |
Number of Dosing Bores | 36 bores |
Filling Accuracy | ±3% (pharmaceutical powder) / ±4% (herbal powder) |
Suitable Materials | Powder, Granule, Pellet |
Power Supply | 60 Hz. Built to your U.S. supply; we confirm the voltage and power with your quote |
Vacuum Requirement | 40 m³/h |
Dust Extraction | 210 m³/h, 24.5 kPa |
Compressed Air | 5 m³/h, 5–7 bar |
Noise Level | < 75 dB(A) |
Overall Dimensions | 1,450 × 1,250 × 2,250 mm (L×W×H) |
Net Weight | 1,800 kg |
Vacuum pump type | Oil-free dry vacuum pump |
Lubrication | Automatic timed lubrication |
Facility requirement | 21 °C ± 3 °C, RH 40–60% |
Model comparison
Model | Output pcs/h | Type | Best for… |
|
NJP-200C | 12,000 | C | Small batches and product development | |
NJP-400C | 24,000 | C | Growing production | |
NJP-800C | 48,000 | C | Standard commercial output | |
NJP-1200D | 72,000 | D | Sticky and herbal powders at scale — dry vacuum pump, auto lubrication | |
NJP-2500C | 150,000 | C | High-volume continuous production | |
NJP-3800C | 228,000 | C | Large-scale manufacturing | |
NJP-5500C | 330,000 | C | Very high volume | You are here |
NJP-7500C | 450,000 | C | Highest output in the range |
The D suffix is a configuration, not just a speed step. C-type machines use a water-ring vacuum pump and external-groove cam lubrication. The D adds a dry vacuum pump — no water to refill, no scale build-up — plus enclosed internal-groove cams with automatic timed oiling, and a nano anti-corrosion coating over the same stainless steel. If your formulation is corrosive or your maintenance team is thin, that’s what you’re paying for.
Butterfly valve hopper with forced vibration
Eliminates material “bridging” using vibration-assisted feeding. Essential for maintaining consistent flow at 5,500 capsules per minute.
100DS indexing box
Featuring a 30mm diameter output shaft. This upgraded driving core provides the heavy-duty stability needed for the most intensive production cycles.
One-piece enclosed turntable
A gapless, CNC-machined frame with dustproof skeleton seals that keep powder out of the drive.
Guideway-driven capsule seeder
An enclosed, precision-guided system that ensures perfectly aligned capsule orientation even at the 5500C’s extreme velocity.
How Much Powder Are You Losing per Batch?
Powder from capsules that fail to separate is drawn into a collector by negative pressure instead of falling onto the platform, so you recover it rather than sweep it up.
Keeping Powder Out of the Drive System
The enclosed turntable runs three years without internal maintenance or manual oiling with a dual-lip skeleton dust ring to prevent powder ingress.
Running at 330,000/h Without Losing Fill Accuracy
Ten stations split separation, filling and locking into separate steps, so the NJP-5500C holds its fill weight at 330,000 capsules an hour.
Industrial Applications
Herbal and botanical extracts
Poor flowability is the classic reason a capsule line stalls. Herbal powders arch above a screw feeder outlet instead of falling through it. The butterfly valve hopper vibrates the material past that point — this is the case it was built for.
Hygroscopic powders
Moisture-absorbing powders stick to the mold holes and stop capsules separating. An air jet clears both mold holes on every rotation, which is what keeps the capsule-feeding success rate from dropping through a shift.
Pellets and powder-plus-pellet
Station five is left open for an optional pellet dosing unit. A machine bought for powder today can run powder-plus-pellet later without going back to the factory — tell us if that’s on your roadmap and we’ll leave the interface in place.
High-value actives and concentrated extracts
When the powder costs more than the capsule, recovery matters more than speed. Two separate lines — one for waste capsules, one for clean powder — mean what you reclaim goes straight back into the batch.
Changeover: what you change and how long it takes
What you changed | What gets adjusted | Roughly how long |
Same capsule, different fill weight | Tamping pin depth on the dosing station | 15–30 minutes |
Fill weight beyond the adjustment range | Swap the dosing disc for a different thickness | 15–30 minutes |
Different capsule size | Full tooling set: upper and lower modules, tamping pins, capsule tubes, alignment combs, feeding combs, dosing disc, alignment bars | 15–30 minutes |
Dosing disc thickness is the second lever. When tamping depth reaches its mechanical limit and you still can’t hit your target fill weight, you change the disc rather than fighting the machine. It’s a physical volume change, not a calibration.
The gaps matter more than they sound. Dosing disc to copper ring: 0.08–0.12 mm. Isolation block to disc: 0.05–0.1 mm. Every disc change means resetting the second one. Too tight and the disc binds; too loose and powder leaks and your fill weight scatters.
Cleaning is the long part. Between products, the powder hopper, dosing ring, upper and lower modules, tamping pins and dosing disc all come out. Parts above the machine table are cleaned with alcohol on lint-free cloth — never gasoline, kerosene, hydrogen peroxide or acetone.
What to check before you order — from any supplier
Ask to see the machine running your powder, not a demo powder
Lactose and starch run beautifully on everything. Ask for a video of your own material, or send a 2 kg sample for a trial run. Any factory that won't do this is telling you something.
Ask what the sustained rate is, not the maximum rate
Catalogue output figures are peak numbers. Ask what the machine holds over an eight-hour shift with your fill weight and your capsule size, and what the reject rate looks like at that speed.
Ask for the operating manual before you pay
If the adjustment procedures aren't in it — tamping pin height, dosing disc clearances, vacuum settings — your operators will be calling the factory every time something drifts.
Ask which parts are wear parts and what they cost
On a capsule filler that means seals, tamping pins and the dosing disc. Get the list and the prices in writing with the quotation.
Ask what the electrical supply actually is
Most machines from Asia ship at 380V / 50Hz as standard. Confirm in writing that yours will arrive configured for your plant, and whether the output figure still holds after the change.
Ask who installs it and who trains your operators
"We provide installation support" can mean an engineer on your floor or a PDF. Ask which, ask for how many days, and ask what happens if commissioning takes longer.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Powder Before You Order
Send us a 2 kg sample of your powder. We run it on a test machine and send you the fill weight figures before you order.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
NJP-5500C FAQ
No. Powder from capsules that fail to separate is drawn into a collector instead of falling onto the platform, and that works the same at full speed.
The enclosed rotary table keeps powder out of the drive, and the lubrication system keeps the gears oiled, so routine maintenance is mostly the wear parts: seals, tamping pins and the dosing disc.
Yes. The butterfly valve hopper with vibration unit is specifically engineered for powders with poor liquidity. It forces consistent material flow, keeping fill weight within ±4% on herbal powder, even at 5,500 capsules a minute.
Lead time depends on the configuration and is confirmed in writing in your quote, along with the shipping time to your port.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us your powder details and your target output
We’ll come back with a machine recommendation, tooling list and a price. If this model isn’t the right size for you, we’ll tell you which one is.
Direct from our factory
Lead time confirmed in your quote
Installation and training available
Spare parts listed in your quote