Automatic Strip Packing Machine

Soft Alu-Alu Heated-Roller Sealing for Tablets, Capsules and Effervescents

220 to 500 mm Film
Air-Cylinder to Full-Servo Cutting
Alu-Alu and Plastic-Plastic

Each tablet is sealed between two soft foils on heated rollers — a full light and moisture barrier, with nothing formed or stretched thin.

What Every Model in the Range Does

Four widths, two cutting systems, and the same sealing method on every one. Here’s what’s built into all of them.

Sealed Flat, Not Formed

Sealed Flat, Not Formed

A blister machine heats plastic and stretches it into a pocket. This machine doesn’t form anything. The tablet sits between two soft aluminium foils and heated rollers press them together around it. The barrier is the full thickness of the foil on both faces.

Vibratory Feeding with Broken-Tablet Screening

Vibratory Feeding with Broken-Tablet Screening-1

Tablets feed from a vibrating hopper, and broken pieces are screened out before they reach the rollers. A fragment sealed into the margin is what causes a leak, so this step matters more than it looks.

Two Heated Rollers, Two Controllers

Two Heated Rollers, Two Controllers

Each sealing roller has its own heater and its own temperature controller. When you switch between Alu-Alu and plastic-plastic, you set each roller to suit the material rather than running both at one setting.

Two-Stage Traction, Clean Cuts

Dual-Stage Traction Guide

The foil is pulled through in two stages, which keeps it flat as it reaches the slitter and the cutter. Flat foil is what gives a clean edge on every strip.

Missing-Tablet Reject, as an Option

Automated Defective Sheet Segregation Compartment

Add a detection and reject system, and any strip with a missing tablet is diverted to its own conveyor and collected separately, so it never reaches your good output.

Tension Balancers and Air Shafts

Tension Balancers

Each foil roll has its own tension balancer, so both webs feed evenly across the full width. Rolls load on pneumatic air shafts with limit rings, so a new roll goes on in the same position every time.

Strip or Blister? Then Which Width?

1. Do you want the tablet visible?

A clear PVC blister shows the product. A foil strip doesn’t. If shelf presence matters more than barrier, you want a blister machine, not this one.

2. Is moisture or light the real problem?

Effervescent tablets, probiotics and light-sensitive vitamins are where a strip earns its place — foil on both faces, nothing stretched thin.

3. How often do you change strip layout?

The SP220 cuts with an air cylinder, set by hand. The SP300 and SP400 cut with a servo, set on the touchscreen. The SP500 runs every station on a servo motion controller. If you change layout between SKUs, skip the SP220.

4. How wide does your layout need to be?

220, 300, 400 or 500 mm. More width means more lanes at the same drum speed — but only if your tablet and strip layout actually fill it. Send us both and we’ll tell you.

What These Machines Pack

Effervescent tablets
Probiotic and moisture-sensitive capsules
Light-sensitive vitamins and botanicals
Lozenges and chewable tablets

Model comparison

Model

Film width

Drum speed

Cutting

Output

Heating

APK-SP220

220 mm

7–14 rpm

Air cylinder

20,000 – 60,000 pcs/h

1.5 kW × 2

APK-SP300

300 mm

7–14 rpm

Servo

20,000–80,000 pcs/h

1.2 kW × 2

APK-SP400

400 mm

7–14 rpm

Servo

20,000–120,000 pcs/h

1.5 kW × 2

APK-SP500

500 mm

6–20 rpm

Full servo, motion controller

Depends on layout

1.5 kW × 2

Output depends on your tablet size and how many lanes fit across the film. Tell us both and we’ll give you your number, not the headline one.

Send us your tablet and your strip layout

Tablet size decides the roller dies; strip layout decides the width and the cutting. Post us a few samples and tell us the layout, and we’ll tell you which model fits — including when it’s the smaller one.

Documentation & Selection Support

Verify our quality standards and simplify your procurement process with our official documentation.

Product Portfolio

Product Portfolio

Specifications for the APK-SP220, SP300, SP400 and SP500: film width, drum speed, cutting, output and heating.
Quality Assurance

Quality Assurance

CE Declaration of Conformity for the APK-SP series.
Roller Pocket

Roller Pocket, Designed from Your Samples

Send us your tablet samples and we'll design the roller pocket and strip layout around them before you commit.

FAQs on Strip Packing Machines

What's the difference between a strip and a blister?

A blister machine heats plastic and stretches it into a pocket, then seals foil over it. A strip machine forms nothing — two soft foils are heat-sealed around the tablet on rollers. Because nothing is stretched, both faces keep the full foil thickness. Blisters show the product and suit taller items; strips give a full light and moisture barrier and fold flat.

Air-cylinder or servo cutting — which do I need?

The SP220 cuts with an air cylinder: reliable, lower cost, and set by hand when you change layout. The SP300 and SP400 cut with a servo, so strip length and cutting stroke are set on the touchscreen. The SP500 puts every station on a servo motion controller. If you change strip layout between SKUs, start at the SP300.

How do you stop broken tablets getting into the seal?

Tablets feed from a vibrating hopper and pass a screen that separates broken pieces before they reach the rollers. A fragment caught in the seal margin is what causes a leak, so this is where most sealing problems are prevented.

How do the wider machines keep the seal even across the full width?

On a 400 or 500 mm roller, the edges lose heat faster than the center, and an outer lane that runs cool won’t seal properly. Each sealing roller has its own heater and its own temperature controller, reading from a sensor in the roller, so the temperature holds across the full width. Send us your foil and we’ll run a strip on the full width so you can check the outer lanes yourself.

What options can I add?

An extra set of roller dies, feeder change parts, one-side or two-side eye-mark registration for printed foil, and a detection and reject system for missing tablets. Tell us which you need at the quotation stage.

Yes. The strip machine can be linked to a downstream cartoner so the two run at matched speeds — if the cartoner slows for a jam, the strip machine slows with it rather than piling strips at the transfer.

How fast can I get spare parts?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Do your machines meet U.S. electrical certification requirements?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

Send us your tablet and your strip layout

Tablet size decides the roller dies. Strip layout decides the width and the cutting. Send us both and we’ll tell you which model you need and what it will actually produce.

  • Reply within one business day
  • Roller pocket designed from your samples
  • We keep your product specs confidential.
Scroll to Top