APK-CE6 Case Erector

The APK-CE6 takes flat corrugated blanks from the magazine, opens them, folds the bottom flaps and tapes them shut. It feeds 1 to 6 erected cases a minute to whatever packs them. If someone on your line is folding cases by hand, this is the station that replaces them.

  • Output— 1 to 6 cases per minute
  • Case size— 280×150×150 to 450×400×400 mm
  • Changeover— about 1 minute, handwheel

Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote

Is the APK-CE6 the right case erector for you?

✓ This is a fit if…

✕ Look elsewhere if…

Technical specification

Parameter

Value

What this means for you

Output

1 – 6 cases / min

Keeps ahead of both our case packers

Case length

280 – 450 mm

Longer cases? Tell us the size

Case width

150 – 400 mm

—

Case height

150 – 400 mm

—

Magazine capacity

100 blanks

How often an operator reloads

Blank material

Standard corrugated board

No special blank needed

Tape

OPP or kraft, 38 or 50 mm

Buy tape locally, not from us

Erecting success rate

≥99.9%

About one reject in a thousand cases

Changeover

About 1 minute, handwheel

No tools, no change parts to store

Power

60 Hz

Built to your local supply. We confirm the voltage and frequency with your quote

Compressed air

0.5 MPa, 300 L/min

Check your compressor — this draws more air than the sealer

Footprint

2,000 × 1,900 mm

Deeper than most stations. Allow for magazine loading

Height

1,450 mm

Below eye level, easy to supervise

Weight

About 600 kg

No special foundation

 

How It Fits With the Other Stations

Machine

What it does

Output

 

APK-CE6 Case Erector

Opens and bottom-tapes the case

1–6 cases/min

You are here

APK-550 Pick & Place Case Packer

Loads bottles or cartons

Up to 24 cases/min

View →

APK-550 Side-Load Case Packer

Loads cartons

Up to 5 cases/min

View →

APK-CS10 Case Sealer

Closes and top-tapes

5–10 cases/min

View →

APK-CP900 All-in-One

All three jobs in one frame

Up to 5 cases/min

View →

Buying all three stations? The APK-CP900 does erecting, packing and sealing in one frame, in less floor space. It runs slower — up to 5 cases a minute. Worth comparing before you buy three machines.

Magazine and blank pick-up

Flat blanks sit in a magazine at the front of the machine. The pick-up opens each one and squares it before the flaps are folded. An operator loads the magazine and does nothing else at this station.

Bottom flap folding and taping

The bottom flaps fold in sequence, then the tape head runs across the seam. Tape is OPP or kraft, 38 or 50 mm wide. You buy it locally.

Handwheel size change

Case size changes on handwheels. About a minute, no tools, nothing to store on a shelf. If you run several case sizes a week, this is the number that matters more than throughput.

Touchscreen with counting and alarms

The screen shows output count, running speed and any fault. Faults stop the machine and say why. There’s also an emergency stop.

Ideal Applications & Industries

Bottled supplements

A bottling line at 60 bottles a minute, 12 to a case, needs 5 cases a minute. This machine erects up to 6.

Cartoned products

Sachets and stick packs in retail cartons, packed into shippers.

Contract packers running several case sizes

A one-minute handwheel changeover matters more here than peak throughput. You change case size between clients, not between shifts.

What changing over involves

What changedWhat you adjustRoughly
Same case, different productNothing on this machine0 min
Case size changesHandwheels at the magazine and the folding stationAbout 1 min
Tape width changes (38 ↔ 50 mm)Tape headAsk us

There are no change parts to buy per case size, and none to store. On a full case packing line the packer and sealer adjust too — ask us for the line number, not just this one.

Three things to check before you buy any case erector

01

Accuracy

Every case should come out square, with the bottom seam properly taped. Ours erects at ≥99.9% success. Ask any supplier for their number and how it's verified at FAT.

02

The manual

A clear English manual is what gets your operator running in a week instead of a month. Ask to see a sample page before you order.

03

Installation and training

Installed, commissioned, and your people taught to run it. Ask what's included and what costs extra.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Check Your Case Before We Quote

Send us your case dimensions and what goes in it. We check them against the machine before we quote, so a size problem shows up now, not at installation.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Questions About the APK-CE6 Case Erector

How much does a case erector cost?

It depends on your case size range and your tape width. Send us the dimensions and we’ll price it. We don’t publish a list price because the same machine varies with configuration.

How long is the lead time?

It depends on the configuration. We confirm the lead time in writing with your quote, before you order.

What tape does it use?

OPP or kraft, 38 or 50 mm wide. Standard tape you can buy locally. We don’t supply consumables.

Does it run on US power?

Yes. We build to your local supply and confirm the voltage and frequency with your quote.

How much air does it need?

0.5 MPa at 300 liters a minute. That’s noticeably more than the sealer draws, so check your compressor before you add both stations.

How long does a case size change take?

About a minute on handwheels. No tools and no change parts.

Are your machines electrically certified for the US?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us your case dimensions.

Case length, width and height decide whether this machine fits. Tape width and your cases-per-day decide whether it’s worth buying at all. Send us both and we’ll tell you honestly.

If you erect fewer than a couple of hundred cases a day, we’ll say so. Buy the packer first.

Send your floor dimensions and we’ll do the layout and space calculation free.

Scroll to Top