DPH-260H High-Speed Rotary Blister Packaging Machine

Your flat-plate machine tops out around 60 punches a minute and the line is waiting on it. This one seals with a continuously rotating roller instead of a platen that presses and lifts. The web never stops — which is where the speed comes from, and also why the pocket depth is limited to 12 mm.

1. Cutting frequency: 80 to 150 a minute, 200 maximum. Cold-formed Alu-Alu runs at roughly half that

2. Sealing: continuous rotary roller, with a much shorter heat contact time than a platen

3. Forming area: 200 × 260 mm

4. Materials: PVC, PTP, cold-formed Alu-Alu and PET/paper/aluminum

5. Drive: six servo axes under one motion controller

6. Forming depth: 12 mm, customizable to 15. Deeper items need a flat-plate machine

Is this the right machine for you?

✓ Yes, if…

✕ Buy something else if…

Technical specification

Feature

DPH-260H

What does it mean to you?

Cutting frequency

80–150/min, 200 max (Alu-PVC)

Cold-formed Alu-Alu runs at roughly half the rate. Ask us for the Alu-Alu figure on your format

Forming area & depth

200 × 260 mm, 12 mm deep (custom to 15)

Half the depth of a flat-plate machine. Check your item height first

Sealing

Continuous rotary roller

Tangential contact, not area contact — much shorter heat exposure

Stroke range

40–150 mm, set on the HMI

—

Material width

Up to 260 mm

—

PVC / PTP

0.25–0.50 | 0.02–0.035 × 260 mm

—

Cold-form Alu-Alu

OPA/ALU/PVC 0.10–0.15 × 260 mm

—

Cooling water

0.1–0.25 MPa, up to 600 L/h, tap water or a chiller

You supply the water connection

Air

 0.4–0.7 MPa, up to 200 L/h

—

Heating

6.0 kW

—

Power supply

24 kW max, three-phase five-wire, 60 Hz. Built to your U.S. supply; we confirm the voltage with your quote

—

Dimensions

3,980 × 1,020 × 1,780 mm (L×W×H)

—

Weight

3,000 kg

Check your floor loading

 

Model comparison

Model

Type

Punch freq.

Output

Forming area

Power

DPP-80

Flat plate

10–33 times/min

1,980 plates/hour

80 mm

2.4 kW

DPP-120H

Flat plate

10–35 times/min

2,400–4,200 plates/hour

120 mm

4.5 kW

DPP-150E

Flat plate

10–40 times/min

3,600–7,200 plates/hour

150 mm

6.5 kW

DPP-180H

Flat plate

10–50 times/min

4,800–9,600 plates/hour

180 mm

8.5 kW

DPP-260H1

Flat plate

10–50 times/min

6,000–12,000 plates/hour

 260 mm

9.5 kW

DPP-260H2

Rotary seal

60–130 times/min

Up to 28,800 plates/hour

260 mm

15 kW

DPH-260H

Rotary

80–150 times/min, 200 max

6,000–18,000 plates/hour

260 mm

24 kW

DPH-380H

Rotary

40–180 times/min, 200 max

Up to 45,000 plates/hour

380 mm

28 kW

Flat plate and rotary are two different machines, not two speeds of one. Flat plate stretches the film against a mold with positive air pressure and a mechanical punch. Rotary forms and seals on a drum with line contact. The difference shows up in material waste, changeover time and what the machine costs you per plate — the table above shows where each one fits.

Continuous Motion Logic

The web moves continuously from forming to filling to sealing, with no stop-start cycle. That’s where the speed comes from, and it’s easier on the drive than a machine that accelerates and brakes on every stroke.

Precision Roller Sealing

Advanced roller-type heat sealing provides consistent pressure and a smaller heat-contact area, making it ideal for high-speed Alu-PVC and tropical blister formats.

Intelligent Servo Control

Six servo axes run forming, traction, sealing and cutting from one motion controller. Format settings are stored as recipes on the touchscreen, so a changeover starts from saved settings rather than manual timing.

High-Mounted Track Feeder

The feeder sits above the forming line and is set to keep pace with the blister web, so feeding doesn’t hold back the cutting speed. It handles capsules and round tablets, as well as square and odd-shaped tablets in Alu-Alu blisters. When you change formats, the feeder is repositioned with a hand lever.

Industry Applications

Flat tablets and standard capsules at volume

Items under 12 mm tall in continuous production. This is what a rotary machine is built for.

Heat-sensitive products

Probiotics, enzymes and vitamins where a platen’s dwell time is the problem. Roller sealing touches the seam tangentially — the heat exposure is a fraction of what an intermittent machine applies.

Tropical blister for humid export markets

ALU/PVC/ALU at high speed, where the second aluminum layer would slow a flat-plate machine more than it slows this one.

Cold-formed Alu-Alu at volume

Runs at roughly half the Alu-PVC rate. Still faster than a flat-plate machine, and the narrower plate margin matters more when the foil costs several times what Alu-PVC does.

What changing over involves

What changed

What you adjust

Roughly

Same format, new batch

Nothing

—

Plate layout changes

Rotary drum molds and rollers

15–30 minutes

Alu-PVC → Alu-Alu

Tooling and feeder. Cutting frequency drops to roughly half

Not a changeover

Servo synchronization means the stations re-align from the recipe rather than by manual timing — that part is on the HMI. The drums and rollers still have to come off and go back on by hand.

A rotary machine trades changeover speed for running speed. If you switch format more than once a week, a flat-plate machine will cost you less in downtime than this one saves.

What to check before you buy

01

The tooling, not the machine

A format set covers four synchronized stations. Ask any supplier who designs the pocket layout, how long a new format takes to make, and what it costs. That's where a blister project succeeds or fails.

02

The feeder, before you order

An Alu-PVC universal feeder cannot run cold-formed Alu-Alu, and it cannot be converted afterwards. Ask which feeder you're being quoted and what it locks you out of.

03

Installation and training

Ask what's included and what costs extra. The answer varies more between suppliers than the machine price does.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Design the Pocket Around Your Product

Send us your tablet or capsule samples and tell us your foil. We design the pocket layout and specify the feeder before we quote, because an Alu-PVC universal feeder can’t be converted to Alu-Alu later.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

DPH-260H Rotary Blister Packaging Machine FAQ

When should I choose rotary over flat-plate?

When your volume is above what a flat-plate machine delivers and your pocket depth is 12 mm or less. The web never stops on a rotary machine, so there’s no acceleration and deceleration cycle limiting the rate. What you give up is forming depth and changeover speed. If your item is tall or you change format often, flat-plate is the better machine — not the older one.

How does rotary sealing help heat-sensitive products?

Unlike flat-plate sealing, which applies heat to a large area for a set duration, Roller Sealing features a much smaller “tangential” contact point. The heat is applied instantaneously as the rollers turn, drastically reducing the total heat exposure time for the product pockets. The sealing drum is water-cooled, which keeps heat away from the product in the pockets. If you run probiotics, enzymes or other heat-sensitive products, tell us and we’ll set the sealing temperature around them.

Can the DPH-260H handle ALU/ALU cold-forming with the same precision as ALU/PVC?

Yes, with Alu-Alu tooling. Cold-formed foil is stretched mechanically rather than softened with heat, so it needs its own forming molds and a feeder that runs Alu-Alu. It runs at roughly half the Alu-PVC rate. Tell us at the quotation stage if Alu-Alu is in your plan.

How does the Multi-Axis Servo System benefit the operator during a changeover?

Traditional machines rely on complex gear trains and manual timing adjustments. The DPH-260H utilizes a Multi-Axis Servo Synchronization system where every major station (forming, traction, cutting) is digitally linked. During a format change, the operator simply selects the recipe on the HMI, and the servo motors automatically re-align to the correct positions, cutting setup time and the guesswork in manual timing

Is the DPH-260H compatible with advanced materials like PET/Paper/ALU?

Yes. Sealing temperature and pressure are set for the laminate you run. Send us a sample of your material and we’ll confirm it on a test run before you order.

Does it run on US power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us your item height and your material

Two numbers decide whether this machine suits you, and neither is speed. Pocket depth on this machine stops at 12 mm. And if you run cold-formed Alu-Alu, the cutting rate drops to roughly half — so the headline figure isn’t your figure

Send us a sample item and tell us which foil you run. If rotary isn’t right, we’ll point you at the flat-plate machine and say so in the first email.

  • Direct from our factory
  • Lead time confirmed in your quote
  • Installation and training available
  • Spare parts listed in your quote
Scroll to Top