APK-GEF50E Automatic Powder Filling Machine with Built-In Weighing

Cans fed automatically, weighed under the filler, corrected every fill

Your label says 2 lb and every tub has to hold 2 lb, at a rate no one person can keep up with. This machine feeds the containers, fills them with a servo auger, and weighs each one on a scale underneath. If the powder’s density shifts, the next fill is corrected — without anyone standing there with a balance.

1. Weighing: load cell under the filling station, corrects the auger every fill

2. Speed: 20 to 40 containers a minute, depending on your powder and fill weight

3. Fill weight: 10 g to 2,000 g, by changing the auger

4. Power: single-phase or three-phase

Is this the right machine for you?

✓ Yes, if…

✕ Buy something else if…

Weighed Under the Filler

A load cell under the filling station weighs every container as it’s filled. The reading goes back to the auger, so the next fill is corrected for whatever the powder did last time — settled, aerated, or changed from batch to batch.

Why Weigh on an Automatic Line

An auger doses by volume, and powder density drifts over a shift. On a semi-automatic filler someone is standing there and can catch it. On an automatic line nobody is, so a drift runs for hours before a spot check finds it. Weighing every fill is how an automatic filler stays on label weight without supervision.

Servo-Driven Auger

The auger runs on a servo motor, so it stops at the same point every cycle and responds to the scale’s correction immediately.

No Container, No Fill

A sensor checks that a container is in place before the auger turns. A gap in the line means no powder on the conveyor.

Technical specification

FeatureAPK-GEF50EWhat it means for you
Filling heads1Need more speed? See the GEF50D
DosingServo auger—
WeighingLoad cell under the filling station, feedback to the augerCorrects every fill
Fill weight10–2,000 gChange the auger for different ranges
Accuracy≤ ±1 g–2 gAsk for it at your fill weight, in grams
Speed20–40/minDepends on your powder and fill weight
PowerSingle-phase or three-phaseBuilt to your local supply; we confirm the voltage and frequency with your quote
ControlsPLC—

Model comparison

Model

Type

Weighing

Fill weight

Speed

Power

APK-GEF50A

Semi-automatic

None — volumetric

10-5000g

10–50/min

1.8 kW

APK-GEF50B

Semi-automatic

Built-in, corrects each fill

10–5,000 g

10–50/min

1.8 kW

APK-GEF50C

Single-head automatic

None — volumetric

1–500 g

25–45/min

2.2 kW

APK-GEF50D

Twin-head automatic

None — volumetric

10–5,000 g

25–60/min

3.5 kW

APK-GEF50E

Single-head automatic, screw-conveyor fed

Built-in, corrects each fill

10–2,000 g

20–40/min

3.0 kW

Two questions decide the model. Does every container have to hit its label weight? Then you want a built-in scale. Can one operator keep up placing containers? If not, you want an automatic model that feeds them for you.

Production Applications

Protein powder tubs

Whey and plant protein in 2 to 5 lb tubs, where the label weight is what a retailer checks first.

Pre-workout and greens

Fine, sticky powders that drift the most in weight as they settle. On an automatic line, that’s exactly what the scale is for.

Collagen and creatine

Fine, free-flowing powders in jars, where a gram over on every container adds up over a year.

Meal replacements

Blends that vary from batch to batch. The scale corrects for each batch rather than relying on one setting.

What changing over involves

What changed

What you adjust

Roughly

Same container, different fill weight

Set the new target weight on the screen

A few minutes

Different container size

Guide rails, adjusted on handwheels — no change parts

15-30 Minutes

Different powder

Clean the hopper and auger

15-30 Minutes

Fill weight outside the auger’s range

Change the auger

15-30 Minutes

The auger sets the fill range, so tell us your smallest and largest fill and we’ll supply the augers to cover both.

What to check before you buy

01

Fill weight against your label, not a percentage

Ask any supplier for accuracy at your fill weight, in grams. "±1%" means something different at 50 g and at 2 kg.

02

Whether it weighs, or only counts turns

A volumetric auger drifts as the powder settles. This machine doesn't weigh — so plan who checks fills and how often, or choose the model with a built-in scale.

03

Installation and training

Ask what's included and what costs extra.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Powder Before You Order

Send us a sample and we fill it on the machine before you order, so you see the weight spread on your own product. Tell us your smallest and largest fill and we supply the augers to cover both.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Fully Expanded Technical FAQ for APK-GEF50E

Why weigh every fill on an automatic line?

Because nobody is standing at the machine. An auger doses by volume, and powder density drifts as the hopper empties and from batch to batch. On an automatic line that drift can run for hours before a spot check finds it. Weighing every fill and correcting the auger is how you stay on label weight without supervision.

What's the difference between this and the GEF50C?

The scale. Both feed containers automatically and fill with a servo auger. This one weighs every container and corrects the next fill; the GEF50C doesn’t. If spot checks are enough for your quality plan, the GEF50C costs less.

What accuracy can I expect?

Within ±1–2 g, depending on your powder and fill weight. Send us a sample and we’ll tell you what to expect at your fill weight.

What happens if a container is missing?

 A sensor checks that a container is in place before the auger turns, so a gap in the line means no powder spilled.

Does it run on single-phase power?

Yes, to order. We build to your local supply and confirm the voltage and frequency with your quote.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us your label weight and your container.

The weight on your label is the number this machine is built around. Send us that, your container size and your daily volume, and we’ll tell you what accuracy to expect and whether you need the scale at all.

  • Direct from our factory
  • Lead time confirmed in your quote
  • Installation and training available
  • Spare parts listed in your quote
Scroll to Top