APK-GEF50B Semi-Automatic Powder Filling Machine with Built-In Weighing
Servo auger with weight feedback, 10 g to 5 kg, 10 to 50 fills a minute
You’re filling protein or pre-workout by hand with a scoop and a scale, and every tub comes out a few grams different. This machine does the dosing for you: a servo-driven auger fills the tub or pouch you hold under it, and a built-in scale checks the weight and corrects the next fill. From 10 g sample packs to 5 kg tubs, by changing the auger.
1. Fill weight: 10 g to 5,000 g, by changing the auger
2. Weight feedback: built-in scale, 1 g resolution, corrects the auger as your powder’s density changes
3. Speed: 10 to 50 fills a minute, depending on fill weight and operator
4. Power: three-phase, or single-phase to order, 1.8 kW
Is this the right machine for you?
✓ Yes, if…
- Every tub or pouch has to hit the weight on its label
- Your powder is sticky, or its density changes as the hopper empties
- Your fills are between 10 g and 5 kg
- One operator placing each container can keep up with your volume
- Your site only has single-phase power
✕ Buy something else if…
- Spot checks on a separate scale are enough for you → the APK-GEF50A does the same filling without the built-in scale, for less
- One operator can't keep up → the APK-GEF50E keeps the weighing and feeds containers automatically
- Your product is a liquid or a paste → augers dose powders and fine granules only
- You're filling single-serve sticks or sachets → that's a stick pack machine
Weight Feedback That Tracks Your Powder
An auger doses by volume — the same number of turns every time. But powder settles, aerates and changes density as the hopper empties, so the same volume weighs a little different through the shift. This machine weighs each fill and feeds the result back to the auger, so the next fill is corrected for the density change instead of drifting with it.
Servo-Driven Auger
The auger runs on a servo motor rather than a clutch-brake drive. It stops where it’s told to, every time, and the speed is set on the screen. That precision is what makes the weight correction worth having.
Sealed Hopper You Can See Into
The 50-litre hopper is a sealed stainless-and-glass combination, so the operator can see the powder level without opening it and the dust stays in. It opens from the side for cleaning, and the agitator is driven by a low-maintenance gear motor.
Dust Pickup at the Outlet, Residue Tray Underneath
A dust pickup at the filling outlet recovers the powder that would otherwise settle around the machine. The work table raises and lowers to suit your container height, and a drawer underneath catches spills.
Technical specification
Feature | APK-GEF50B | What it means for you |
Dosing | Servo auger with weight feedback | — |
Fill weight | 10–5,000 g | Change the auger for different ranges |
Weighing range | 1–6,000 g, 1 g resolution | Built in, not an add-on |
Accuracy | Under 100 g: ±0.5–1 g | 100–1,000 g: ±0.5–1% | Over 1,000 g: ±0.25–0.5% | Heavier fills hold a tighter percentage |
Speed | 10–50 fills/min | Depends on fill weight and how fast the operator places containers |
Hopper | 50 L | — |
Recipes | 10 stored | Recall settings when you switch powder or size |
Power | Three-phase, or single-phase to order; 60 Hz | Built to your local supply; we confirm the voltage and frequency with your quote |
Installed power | 1.8 kW | — |
Dimensions | 800 × 1,200 × 2,150 mm | — |
Weight | 260 kg | — |
Contact parts | SUS304 | — |
Controls | PLC with touchscreen and servo drive | — |
Model comparison
Model | Type | Weighing | Fill weight | Speed | Power |
APK-GEF50A | Semi-automatic | None — volumetric | 10-5000g | 10–50/min | 1.8 kW |
APK-GEF50B | Semi-automatic | Built-in, corrects each fill | 10–5,000 g | 10–50/min | 1.8 kW |
APK-GEF50C | Single-head automatic | None — volumetric | 1–500 g | 25–45/min | 2.2 kW |
APK-GEF50D | Twin-head automatic | None — volumetric | 10–5,000 g | 25–60/min | 3.5 kW |
APK-GEF50E | Single-head automatic, screw-conveyor fed | Built-in, corrects each fill | 10–2,000 g | 20–40/min | 3.0 kW |
Two questions decide the model. Does every container have to hit its label weight? Then you want a built-in scale. Can one operator keep up placing containers? If not, you want an automatic model that feeds them for you.
Production Applications
Protein powder tubs
Whey, plant protein and collagen in 1 to 5 lb tubs. Heavier fills are where the weight feedback holds its tightest percentage.
Pre-workout and greens
Fine, often sticky powders that bridge in a hopper and drift in weight as they settle. The agitator keeps them moving; the scale catches the drift.
Sample packs and trial sizes
Small fills from 10 g, in pouches or jars, when you’re testing a new flavor before a full run.
Drink mixes and meal replacements
Free-flowing blends in pouches or canisters, several SKUs a day. Settings for each are stored and recalled.
What changing over involves
| What changed | What you adjust | Roughly |
| Same powder, different fill weight | Recall the recipe on the screen | A few minutes |
| Different powder, same range | Clean the hopper and auger, recall the recipe | 15-30 Minutes |
| Fill weight outside the current auger’s range | Change the auger | 15-30 Minutes |
| Different container height | Raise or lower the table | Minutes |
Ten recipes are stored on the machine. The auger sets the fill range, so tell us your smallest and largest fill and we’ll supply the augers to cover them.
What to check before you buy
Fill weight against your label, not a percentage
Ask any supplier for accuracy at your fill weight, in grams. "±1%" means something different at 50 g and at 2 kg.
Whether it weighs, or only counts turns
Whether it weighs, or only counts turns A volumetric auger drifts as the powder settles. Ask whether the machine weighs each fill and corrects itself, or relies on the operator to check.
Installation and training
Ask what's included and what costs extra.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Powder Before You Order
Send us a sample and we fill it on the machine before you order, so you see the weight spread on your own product. Tell us your smallest and largest fill and we supply the augers to cover both.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Dedicated FAQ for APK-GEF50B
The machine weighs each fill on a built-in scale with 1 g resolution. If the powder’s density changes — as it does when the hopper empties or the powder settles — the weight shifts, and the machine adjusts the auger for the next fill.
Under 100 g, within ±0.5 to 1 g. From 100 g to 1 kg, within ±0.5 to 1%. Over 1 kg, within ±0.25 to 0.5%. The heavier the fill, the tighter the percentage.
If your powder is free-flowing and steady, and spot checks on a separate balance are enough for your quality plan, the GEF50A does the same filling for less. If every container has to hit its label weight, or your powder is sticky or variable, the scale is what keeps you there without someone checking every fill.
The hopper is sealed and has an agitator to stop powder bridging, and a dust pickup at the outlet recovers what would otherwise escape. For very poorly flowing powders, send us a sample — auger choice matters more than any setting.
Yes. Ten recipes are stored. Clean the hopper and auger between powders, and change the auger if the new fill is outside its range.
Yes, to order. Standard is three-phase, and single-phase is available. We build to your local supply and confirm the voltage and frequency with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us your powder and your fill weight
Fill weight decides the auger. The powder decides how it behaves in the hopper. Send us a sample and tell us your smallest and largest fill, and we’ll tell you what accuracy to expect in grams.
Direct from our factory
Lead time confirmed in your quote
Installation and training available
Spare parts listed in your quote