APK-GEF50A Semi-Automatic Auger Powder Filling Machine
Volumetric auger dosing — the simplest step up from hand-scooping
You’re filling tubs or pouches by hand with a scoop, and it’s slow. This machine does the dosing: an auger fills the container you hold under it by volume, the same amount every cycle. It doesn’t weigh. If your label weight has to be exact on every container, look at the model with a built-in scale instead.
1. Fill weight: 10 g to 5,000 g, by changing the auger
2. Dosing: volumetric auger, no built-in scale
3. Speed: 10 to 50 fills a minute
4. Power: three-phase, or single-phase to order
Is this the right machine for you?
✓ Yes, if…
- Your powder is free-flowing and its density stays fairly steady
- Your fill tolerance is loose, or you already check weights on a separate scale
- You want the simplest, lowest-cost way to stop hand-scooping
- One operator placing each container can keep up with your volume
✕ Buy something else if…
- Your label weight has to be right on every tub → an auger doses by volume, and the same volume weighs a little different as the powder settles. The model with a built-in scale weighs every fill and corrects the next one
- Your powder is sticky or its density changes through the day → pre-workout, greens and some proteins drift the most. That's where the scale earns its cost
- You need nobody standing at the machine → our twin-head automatic filler runs cans on a turntable, 25 to 60 a minute
- You're filling single-serve sticks or sachets → that's a stick pack machine
Multi-Specification Flexible Changeover Matrix
Specifically optimized for high-mix, small-to-medium output manufacturing parameters where factories process multiple powder recipes in a single day. The flexible tool-less assembly allows operators to execute complete product or specification changeovers with zero extended line downtime.
Anti-Dust Sanitary Isolation Enclosure
Engineered to handle highly dusting, poor-fluidity pharmaceutical and chemical powders. The fully sealed hopper joints and precision-ground screw tolerances isolate active compounds to suppress powder scattering, eliminate material waste, and protect strict cleanroom air standards.
Dynamic Density Weight Compensation
Unlike open-loop fillers that suffer from weight drift as the powder level changes, our integrated weight-feedback logic actively detects density alterations and instantly communicates screw calibration adjustments back to the PLC processor to lock in rigid batch consistency.
Technical specification
Feature | APK-GEF50A | What it means for you |
Dosing | Volumetric auger | No built-in scale — check weights on a separate balance |
Fill weight | 10–5,000 g | Change the auger for different ranges |
Accuracy | ±0.25%-0.5% | Ask for it at your fill weight, in grams |
Speed | 10–50 fills/min | Depends on fill weight and how fast the operator places containers |
Power | 1.8 kW | Built to your local supply; we confirm the voltage and frequency with your quote |
Dimensions | 800 × 1,200 × 2,150 mm (L×W×H) | — |
Weight | 260 kg | — |
Contact parts | SUS304 | — |
Controls | PLC | — |
Model comparison
Model | Type | Weighing | Fill weight | Speed | Power |
APK-GEF50A | Semi-automatic | None — volumetric | 10-5000g | 10–50/min | 1.8 kW |
APK-GEF50B | Semi-automatic | Built-in, corrects each fill | 10–5,000 g | 10–50/min | 1.8 kW |
APK-GEF50C | Single-head automatic | None — volumetric | 1–500 g | 25–45/min | 2.2 kW |
APK-GEF50D | Twin-head automatic | None — volumetric | 10–5,000 g | 25–60/min | 3.5 kW |
APK-GEF50E | Single-head automatic, screw-conveyor fed | Built-in, corrects each fill | 10–2,000 g | 20–40/min | 3.0 kW |
Two questions decide the model. Does every container have to hit its label weight? Then you want a built-in scale. Can one operator keep up placing containers? If not, you want an automatic model that feeds them for you.
Production Applications
Drink mixes and meal replacements
Free-flowing blends in pouches or canisters. These hold their volume well enough for a volumetric auger.
Protein powder
Whey and plant protein in tubs or bags. Standard free-flowing blends dose well by volume; spot-check weights as you go.
Sample packs and trial sizes
Short runs of a new flavor, where a spot check every few fills is all the control you need.
Coffee, cocoa and fine free-flowing powders
Powders that don’t cake or bridge. If yours does — pre-workout and greens often do — the model with a scale is the safer choice.
What changing over involves
What changed | What you adjust | Roughly |
Same powder, different fill weight | Set the new dose on the controller | A few minutes |
Different powder, same range | Clean the hopper and auger | 15-30 Minutes |
Fill weight outside the current auger’s range | Change the auger | 15-30 Minutes |
The auger sets the fill range, so tell us your smallest and largest fill and we’ll supply the augers to cover both.
What to check before you buy
Fill weight against your label, not a percentage
Ask any supplier for accuracy at your fill weight, in grams. "±1%" means something different at 50 g and at 2 kg.
Whether it weighs, or only counts turns
A volumetric auger drifts as the powder settles. This machine doesn't weigh — so plan who checks fills and how often, or choose the model with a built-in scale.
Installation and training
Ask what's included and what costs extra.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Powder Before You Order
Send us a sample and we fill it on the machine before you order, so you see the weight spread on your own product. Tell us your smallest and largest fill and we supply the augers to cover both.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Semi-Automatic Auger Powder Filling Machine Frequently Asked Questions
Up to a point. An agitator keeps the powder moving over the auger, but a volumetric filler is only as consistent as the powder’s density. For sticky or poorly flowing powders, send us a sample first — or look at the model with a built-in scale.
Yes. Clean the hopper and auger between powders, and change the auger if the new fill is outside its range.
No. It doses by volume. You check weights on a separate scale, at whatever frequency your quality plan calls for. If you’d rather the machine did that for you, our model with a built-in scale weighs every fill and corrects the next one.
Ask us before you order. If you think you’ll need a scale, the APK-GEF50B has one built in, and buying it now usually costs less than adding one later.
Yes, to order. We build to your local supply and confirm the voltage and frequency with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us your powder and your fill weight
Fill weight decides the auger. How your powder flows decides whether volume alone is enough, or whether you need the scale. Send us a sample and tell us your fill range, and we’ll tell you which one fits.
Direct from our factory
Lead time confirmed in your quote
Installation and training available
Spare parts listed in your quote