APK-GEF50E Automatic Powder Filling Machine with Built-In Weighing
Cans fed automatically, weighed under the filler, corrected every fill
Your label says 2 lb and every tub has to hold 2 lb, at a rate no one person can keep up with. This machine feeds the containers, fills them with a servo auger, and weighs each one on a scale underneath. If the powder’s density shifts, the next fill is corrected — without anyone standing there with a balance.
1. Weighing: load cell under the filling station, corrects the auger every fill
2. Speed: 20 to 40 containers a minute, depending on your powder and fill weight
3. Fill weight: 10 g to 2,000 g, by changing the auger
4. Power: single-phase or three-phase
Is this the right machine for you?
✓ Yes, if…
- Every container has to hit the weight on its label
- One operator placing containers can't keep up any more
- Your powder is sticky, or its density changes as the hopper empties
- You fill rigid containers — tubs, cans or jars
✕ Buy something else if…
- Spot checks on a separate scale are enough → the APK-GEF50C does the same automatic filling without the scale, for less
- Your volume is low and one operator is enough → the semi-automatic APK-GEF50B keeps the scale and costs less
- One head can't keep up → the twin-head APK-GEF50D fills two at once
- You fill pouches or bags → this machine handles rigid containers
Weighed Under the Filler
A load cell under the filling station weighs every container as it’s filled. The reading goes back to the auger, so the next fill is corrected for whatever the powder did last time — settled, aerated, or changed from batch to batch.
Why Weigh on an Automatic Line
An auger doses by volume, and powder density drifts over a shift. On a semi-automatic filler someone is standing there and can catch it. On an automatic line nobody is, so a drift runs for hours before a spot check finds it. Weighing every fill is how an automatic filler stays on label weight without supervision.
Servo-Driven Auger
The auger runs on a servo motor, so it stops at the same point every cycle and responds to the scale’s correction immediately.
No Container, No Fill
A sensor checks that a container is in place before the auger turns. A gap in the line means no powder on the conveyor.
Technical specification
| Feature | APK-GEF50E | What it means for you |
| Filling heads | 1 | Need more speed? See the GEF50D |
| Dosing | Servo auger | — |
| Weighing | Load cell under the filling station, feedback to the auger | Corrects every fill |
| Fill weight | 10–2,000 g | Change the auger for different ranges |
| Accuracy | ≤ ±1 g–2 g | Ask for it at your fill weight, in grams |
| Speed | 20–40/min | Depends on your powder and fill weight |
| Power | Single-phase or three-phase | Built to your local supply; we confirm the voltage and frequency with your quote |
| Controls | PLC | — |
Model comparison
Model | Type | Weighing | Fill weight | Speed | Power |
APK-GEF50A | Semi-automatic | None — volumetric | 10-5000g | 10–50/min | 1.8 kW |
APK-GEF50B | Semi-automatic | Built-in, corrects each fill | 10–5,000 g | 10–50/min | 1.8 kW |
APK-GEF50C | Single-head automatic | None — volumetric | 1–500 g | 25–45/min | 2.2 kW |
APK-GEF50D | Twin-head automatic | None — volumetric | 10–5,000 g | 25–60/min | 3.5 kW |
APK-GEF50E | Single-head automatic, screw-conveyor fed | Built-in, corrects each fill | 10–2,000 g | 20–40/min | 3.0 kW |
Two questions decide the model. Does every container have to hit its label weight? Then you want a built-in scale. Can one operator keep up placing containers? If not, you want an automatic model that feeds them for you.
Production Applications
Protein powder tubs
Whey and plant protein in 2 to 5 lb tubs, where the label weight is what a retailer checks first.
Pre-workout and greens
Fine, sticky powders that drift the most in weight as they settle. On an automatic line, that’s exactly what the scale is for.
Collagen and creatine
Fine, free-flowing powders in jars, where a gram over on every container adds up over a year.
Meal replacements
Blends that vary from batch to batch. The scale corrects for each batch rather than relying on one setting.
What changing over involves
What changed | What you adjust | Roughly |
Same container, different fill weight | Set the new target weight on the screen | A few minutes |
Different container size | Guide rails, adjusted on handwheels — no change parts | 15-30 Minutes |
Different powder | Clean the hopper and auger | 15-30 Minutes |
Fill weight outside the auger’s range | Change the auger | 15-30 Minutes |
The auger sets the fill range, so tell us your smallest and largest fill and we’ll supply the augers to cover both.
What to check before you buy
Fill weight against your label, not a percentage
Ask any supplier for accuracy at your fill weight, in grams. "±1%" means something different at 50 g and at 2 kg.
Whether it weighs, or only counts turns
A volumetric auger drifts as the powder settles. This machine doesn't weigh — so plan who checks fills and how often, or choose the model with a built-in scale.
Installation and training
Ask what's included and what costs extra.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Powder Before You Order
Send us a sample and we fill it on the machine before you order, so you see the weight spread on your own product. Tell us your smallest and largest fill and we supply the augers to cover both.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Fully Expanded Technical FAQ for APK-GEF50E
Because nobody is standing at the machine. An auger doses by volume, and powder density drifts as the hopper empties and from batch to batch. On an automatic line that drift can run for hours before a spot check finds it. Weighing every fill and correcting the auger is how you stay on label weight without supervision.
The scale. Both feed containers automatically and fill with a servo auger. This one weighs every container and corrects the next fill; the GEF50C doesn’t. If spot checks are enough for your quality plan, the GEF50C costs less.
Within ±1–2 g, depending on your powder and fill weight. Send us a sample and we’ll tell you what to expect at your fill weight.
A sensor checks that a container is in place before the auger turns, so a gap in the line means no powder spilled.
Yes, to order. We build to your local supply and confirm the voltage and frequency with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us your label weight and your container.
The weight on your label is the number this machine is built around. Send us that, your container size and your daily volume, and we’ll tell you what accuracy to expect and whether you need the scale at all.
- Direct from our factory
- Lead time confirmed in your quote
- Installation and training available
- Spare parts listed in your quote