CGN-208S Semi-Automatic Capsule Filling Machine for Pellets and Powders
The CGN-208S fills coated pellets and powders into sizes #000 to #4 at 12,000 to 24,000 capsules an hour. Pellets fall through a sized outlet instead of being pushed by a propeller, so time-release coatings aren’t ground down.
1. 12,000–24,000 capsules/hour
2. Pellet dosing unit plus powder hopper
3. Horizontal pneumatic locking; Siemens PLC and touchscreen
Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote
Is the CGN-208S the right machine for you?
✓ It's a fit if…
- You fill coated pellets, or pellets and powder in different products
- You need 12,000 to 24,000 capsules an hour
- You use sizes #000 to #4
✕ Look elsewhere if…
- You only fill powder → the CGN-208D1 costs less
- You fill liquids or oils → the CGN-208X
- You need more than 24,000 an hour → tell us; we'll look at the options
Technical specification
| Specification | CGN-208S | What it means for you |
| Output | 12,000–24,000 capsules/hour (one mold set) | Depends on capsule size and operator speed |
| Capsule sizes | #000, #00, #0, #1, #2, #3, #4 | Covers the large sizes supplements often use |
| Capsule separation | Automatic, by separation motor | No turning the mold by hand |
| Materials | Pellets and powders | Pellet unit and powder hopper |
| Pellet dose | Set by the size of the outlet | Feed speed is fixed for pellets |
| Powder dose | Hopper speed and turntable speed | Same as the D1 |
| Locking | Horizontal, pneumatic | Cover, lock and eject run in one cycle |
| Control | Siemens PLC, touchscreen (English/Chinese) | Speeds are entered as numbers, so the next batch runs the same way |
| Qualified rate | ≥98% | Share of capsules separated, filled and locked correctly |
| Power | 60 Hz | Built to your U.S. supply; we confirm the voltage with your quote |
| Total load | 2.12 kW | |
| Compressed air | 0.7 MPa, 0.03 m³/min | A small shop compressor is enough |
| Vacuum pump | 40 m³/h, supplied | No cooling water needed |
| Dimensions | 1,130 × 700 × 1,600 mm | Leave room to move the mold |
| Net weight | 400 kg |
Compare the CGN-208 Series
Five models, one frame. What changes is what they fill, how they lock and how fast they run.
Model | Output (capsules/hour) | Capsule sizes | Locking | Best for |
|
CGN-208D | 10,000–25,000 | #0–#4 | Vertical, foot pedal | Free-flowing powders on a tight budget, moving off manual boards | |
CGN-208D1 | 12,000–24,000 | #000–#4 | Horizontal, pneumatic | Fine or light powders, and repeat batches set on a touchscreen | |
CGN-208D2 | 38,000–43,000 | #000–#4 | Horizontal, pneumatic | Powder products that have outgrown a single-head machine | |
CGN-208S | 12,000–24,000 | #000–#4 | Horizontal, pneumatic | Coated time-release pellets, and powder on the same machine | |
CGN-208X | 12,000–24,000 | #000–#4 | Horizontal, pneumatic | Oil and liquid products in trials and small runs |
Still not sure? Send us your product and daily output, and we’ll tell you which model fits.
Pellet Dosing Unit
Pellets drop through an outlet sized for your dose. Nothing grinds against them on the way in, which protects time-release coatings.
Powder Hopper for Powder Products
The machine also has a powder hopper and propeller feed, so you can run powder products on the same machine.
Same Sowing and Automatic Separation as the D1
The sowing unit uses the design from our automatic fillers, and a separation motor turns the mold under vacuum so the capsules open.
Horizontal Pneumatic Locking
Capsules are locked flat, so pellets and powder stay in the body.
CGN-208S Semi-automatic Capsule Filling Machine Industry Applications
Time-Release Pellet Supplements
Coated pellets that release over hours, where a damaged coating changes how the product works.
Pellet and Powder in Separate Products
One machine for a pellet product and a powder product, by switching the dosing unit.
Pellet Product Trials
Short runs of a new pellet formula before a larger machine.
What Changes When You Switch Products
There’s no single changeover time. It depends on what you’re changing.
What you’re changing | What you do | About how long |
A new product, same capsule size | Take off the hopper and mold, rinse with water, wipe with alcohol and let them dry. Then set the hopper and turntable speeds for the new powder. | 15–30 minutes |
A new fill weight, same product | Powder: enter new hopper and turntable speeds on the touchscreen. Pellets: fit an outlet of a different size. | Minutes for powder; 15–30 minutes for pellets |
A new capsule size (#000 to #4) | Change the mold and the sowing parts for that size: sowing tube, capsule comb, pressing head and orientation device. | 15–30 minutes |
Cleaning counts as downtime too. Tell us which products and capsule sizes you plan to run, and we’ll supply the parts for each size with the machine.
What to check before you buy
Fill Accuracy
Ask for fill weights from a test run on your own powder, not a sample powder. That's the only number that tells you how your product will fill.
Operating Manual
The machine ships with an operating manual in English, and the touchscreen models have an English interface.
Commissioning and Training
Ask who sets the machine up and trains your operator, and what it costs. Our answer is in your quote.
Why Choose AIPAK?
One Point of Contact
One engineer handles your machine from quote to commissioning, so you’re not chasing several people for one answer.
We Run Your Powder Before You Order
Send us your powder and your capsules. We’ll fill them on the machine and send you the video and the fill weights.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
CGN-208S: Comprehensive Technical FAQ
Pellets fall through an outlet sized for your dose instead of being pushed by a propeller. You set the dose by changing the outlet size; the feed speed itself is fixed.
Yes. It has a powder hopper with a propeller feed, set the same way as on the D1.
If a whole batch separates poorly, check the vacuum pump’s filter bag first. A clogged bag weakens the vacuum. Clean it every two to four weeks, depending on how much you run.
It fills standard machine-made capsules. If you use HPMC, send us a few hundred empty capsules with your sample so we can check separation on your brand.
Sizes #000 to #4, each with its own mold set.
It depends on your product. The S has the pellet dosing unit; the D1 fills powder only and costs less. If you only fill powder, choose the D1.
Yes. Under U.S. federal rules, a capsule filling machine counts as an encapsulating machine, and its import must be declared to the DEA on Form 452 before it arrives. We supply the machine details you need for the filing. Confirm the exact requirements with your customs broker.
Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.
Customers Also Interested In...
Send Us Your Powder and Capsule Size
Tell us what you’re filling, your capsule size and how many capsules you need a day. An engineer replies within one business day with the model that fits and why.
- Direct from our factory
- Lead time confirmed in your quote
- Installation and training available
- Spare parts listed in your quote