Home » NYF-300 Liquid Capsule Filling and Sealing Line
NYF-300 Liquid Capsule Filling and Sealing Line
The NYF-300 fills liquid into two-piece capsules and seals the joint, at 18,000 capsules per hour. If you’re making fish oil, CoQ10 or oil-based botanicals and you’ve outgrown filling by hand, this is where automated liquid encapsulation starts. It runs 00# to 4#, gelatin or veggie caps.
- 18,000 capsules per hour— one operator, filling through to dried and discharged
- #00 to #4, gelatin or vegetable capsules— you don’t buy a second machine to switch shell types
- Fill accuracy ±2%— what your label says is what goes in the capsule
Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote
Is the NYF-300 the right size for you?
✓ This is a fit if…
- You're filling oils, suspensions or microemulsions — fish oil, omega-3, CoQ10, vitamin E, botanical extracts
- You need up to 18,000 capsules per hour
- Your capsules are 00# to 4#, gelatin or vegetable
- You run more than one product on the same line and need to change over regularly
- You're moving up from hand-filling or a benchtop unit
- You can hold your room at 20 °C and 40–55% humidity — the sealing adhesive needs it
✕ Look elsewhere if…
- You need more than 18,000/hour → look at the NYF-500 (30,000/h) or NYF-1000 (60,000/h)
- You're filling powder or granules → that's a different machine. Ask us about powder capsule fillers
- You want one-piece softgels → you need a softgel encapsulator, not this. We build those too — tell us your product and we'll say which one fits
- Your room can't hold 20 °C and 40–55% RH → talk to us first. Outside that range, the seal doesn't cure properly and you'll see leakers
- Your fill is thin and water-based → it can wick into the shell wall before the seal sets. Send us a sample before you buy
Technical specification
Parameter | Value | What this means for you |
Output | 18,000 capsules / hour | About 2,400 bottles of 60 in an 8-hour shift |
Capsule sizes | #00 to #4 | Gelatin and vegetable caps on the same machine |
Fill types | Solutions, suspensions, microemulsions, hot-melt | Oils, emulsions and waxy fills all run here |
Fill accuracy | ±2% | Your label claim holds without over-filling to cover variance |
Segment bores | 6 | 6 capsules filled per index |
Changeover time | 30-120mins | How long you stop between products |
Power supply | 9 kW, 60 Hz | Built to your U.S. supply; we confirm the voltage with your quote |
Compressed air | 0.6 MPa | Check your existing compressor covers it |
Dust extraction | 180 m³/h | Supplied separately — ask if you need it quoted |
Footprint (L × W × H) | 3,800 × 900 × 1,900 mm | Add clearance around it for service access |
Machine weight | 2,300 kg | Check your floor loading and door width |
Operating noise | ≤ 75 dB(A) | Normal for a production room |
Control system | PLC and touchscreen | Fill volume set by typing a number |
Dosing pumps | 6 × industrial ceramic | No rubber seals to swell against oils |
Add service clearance around the footprint above — the drying section needs access from both sides.
Model comparison
Model | Output | Bores | Best for… |
NYF-300 | 18,000 /h | 6 | Brands running under 3 million capsules a month, 2–5 SKUs |
NYF-500 | 30,000 /h | 8 | Brands past 3 million a month who don’t yet need a 16-bore line |
NYF-1000 | 60,000 /h | 16 | High-volume contract manufacturers, and combination products needing two solid components |
All three run the same process — same ±2% dosing, same sealing method, same capsule range. What changes is speed and bore count.
Ceramic dosing pumps
Six ceramic pumps meter the fill, servo-driven and set from the touchscreen. Ceramic holds a tight sliding fit without a rubber seal, so there’s nothing to swell or degrade against oils and solvents. You change the dose by typing a number, not by stripping the pump.
Enclosed rotary turntable
The 10-station turntable is machined from one piece, so there are no splice gaps for product to collect in. Upper and lower molds move separately — the lower slides out, the upper lifts. Rated three years without maintenance.
Fiber detection
Twelve fiber sensors check whether each capsule has separated. When one hasn’t, the system tells the filling station to skip that bore, then tells the reject station to throw the capsule out. You lose the capsule, not the oil in it — which matters when your fill costs more than the shell.
Free-hanging drying moulds
After sealing, capsules go into hanging moulds that travel a serpentine path. Each capsule stays face-up the whole time, so a wet seal never touches another capsule or a tray. Tumble drying works for softgels; it doesn’t work for a seal that’s still setting.
Ideal Applications & Industries
Fish oil and omega-3
Oil fills wick into the shell if the seal isn’t right. The double-pass sealing wheel puts adhesive on twice — the first pass wets the seam, the second builds the film.
CoQ10 and fat-soluble vitamins
These cost more per kilo than most fills. The fiber detection skips dosing on any capsule that didn’t open, so you don’t pump expensive oil into a shell that’s heading for the reject bin.
Botanical extracts and oil-based blends
You can run gelatin one week and vegetable caps the next on the same machine. Tell us which shell you’re using — it changes how we set the separation station and the sealing temperature.
What changing over actually involves
Parts to Replace | Adjustment Points | Changeover Time |
Same capsule, different dose | Type the new fill volume on the screen. Nothing comes apart | 15–30 minutes |
Same capsule, different product | Ceramic pumps and material hopper have to be cleaned. No exceptions | 15–30 minutes+ your cleaning time |
Different capsule size | Upper and lower molds, transfer tray and drying molds all change | 15–30 minutes |
Quick to take apart where it counts. The drying molds hang free rather than being bolted in, so they come off quickly for a size change or cleaning.
Cleaning is part of the stop. Between products, the ceramic pumps and material hopper must be cleaned. Budget that time — it’s usually longer than the mechanical change.
One thing to teach your operators. The ceramic rods and plugs are lapped in matched pairs. Swap one between pumps and the fit is gone for good. Six pumps means six pairs that look identical. It’s in the manual and we cover it in training.
Three things to check before you buy any liquid capsule line
Accuracy
Your label says 500 mg. The machine has to put 500 mg in, every capsule, all shift. Ask any supplier what their fill tolerance is and how it's measured. Ours is ±2%, and we run your product at factory acceptance testing before the machine ships.
The manual
Your operators need to run this without calling China. Ask to see the English manual before you order — not a translated parts list, an actual operating manual with the maintenance schedule in it.
Installation and training
A machine that arrives and sits is not cheaper than one that arrives and runs. We install it, commission it, and train your operators on your product.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Fill Before You Order
Send us a sample of your fill and tell us your shell type. We run it on the line, seal and dry it, and send you the capsules and the fill weight figures before you order.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Deep Dive FAQ
Price depends on capsule sizes, whether you need the dust extraction unit, and your electrical configuration. Send us your product, target output and capsule size and we’ll quote within 24 business hours. Most quotes include a free layout drawing.
It depends on the configuration and our build schedule. We confirm the lead time in writing in your quote, before you pay a deposit.
If it’s a solution, suspension, microemulsion or a hot-melt fill, most likely yes. Very thin water-based fills can wick into the shell before the seal sets. Send us a sample and we’ll test it.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
It depends what you’re changing. A dose change on the same capsule is set on the touchscreen. A capsule size change means changing the upper and lower molds, the transfer tray and the drying molds. Cleaning between products adds to that — budget for it. The changeover table above shows each case.
Installation and operator training are available, and what’s included is listed in your quote. A commissioning spare parts kit ships with the machine, listed and priced in your quote before you sign.
Tell us which certification your site or your insurer requires. Our factory confirms in writing what the machine meets before production starts.
The machine is 3,800 × 900 × 1,900 mm. Add clearance on both sides for service access — the drying section needs to be reachable. Send us your room dimensions and we’ll draw a layout for free.
Customers Also Interested In...
Send us your product — we'll send back a configuration
Tell us what you’re filling, what capsule size and how much you need per month. We’ll come back with a machine recommendation, a layout drawing and a price. If the NYF-300 isn’t the right size for you, we’ll say so.
Send your room dimensions and we’ll draw a free layout showing where the line goes and how much clearance you need.