NYF-1000 Liquid Capsule Filling and Sealing Line

The NYF-1000 fills liquid into two-piece capsules and seals the joint, at 60,000 capsules per hour on sixteen bores. It’s the top of the range, built for high-volume contract manufacturing, and its two mixing stations can add a pellet or mini-tablet to the liquid in the same capsule. It runs #00 to #4, gelatin or veggie caps.

  • 60,000 capsules per hour— one operator, filling through to dried and discharged
  • #00 to #4, gelatin or vegetable capsules— you don’t buy a second machine to switch shell types
  • Fill accuracy ±2%— what your label says is what goes in the capsule

Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote

Is the NYF-1000 the right size for you?

✓ This is a fit if…

✕ Look elsewhere if…

Technical specification

Parameter

Value

What this means for you

Output

60,000 capsules / hour

About 8,000 bottles of 60 in an 8-hour shift

Capsule sizes

#00 to #4

Gelatin and vegetable caps on the same machine

Fill types

Solutions, suspensions, microemulsions, hot-melt

Oils, emulsions and waxy fills all run here

Fill accuracy

±2%

Your label claim holds without over-filling to cover variance

Segment bores

16

16 capsules filled per index

Changeover time

30-120mins

How long you stop between products

Power supply

60 Hz

Built to your U.S. supply; we confirm the voltage and power with your quote

Compressed air

 0.6 MPa

Check your existing compressor covers it

Dust extraction

180 m³/h

Supplied separately — ask if you need it quoted

Footprint (L × W × H)

4,100 × 1,300 × 2,100 mm

Add clearance around it for service access

Machine weight

3,000 kg

Check your floor loading and door width

Operating noise

≤ 75 dB(A)

Normal for a production room

Control system

PLC and touchscreen

Fill volume set by typing a number

Dosing pumps

16 × industrial ceramic

No rubber seals to swell against oils

Add service clearance around the footprint above — the drying section needs access from both sides.

Model comparison

Model

Output

Bores

Best for…

NYF-300

18,000 /h

6

Brands running under 3 million capsules a month, 2–5 SKUs

NYF-500

30,000 /h

8

Brands past 3 million a month who don’t yet need a 16-bore line

NYF-1000

60,000 /h

16

High-volume contract manufacturers, and combination products needing two solid components

All three run the same process — same ±2% dosing, same sealing method, same capsule range. What changes is speed and bore count.

Ceramic dosing pumps

Sixteen ceramic pumps meter the fill, servo-driven and set from the touchscreen. Ceramic holds a tight sliding fit without a rubber seal, so there’s nothing to swell or degrade against oils and solvents. You change the dose by typing a number, not by stripping the pump.

Enclosed rotary turntable

The turntable is machined from one piece… Upper and lower molds move separately — the lower slides out, the upper lifts. Rated three years without maintenance.

Fiber detection

Fiber sensors check whether each capsule has separated. When one hasn’t, the system tells the filling station to skip that bore, then tells the reject station to throw the capsule out. You lose the capsule, not the oil in it — which matters when your fill costs more than the shell.

Free-hanging drying moulds

After sealing, capsules go into hanging moulds that travel a serpentine path. Each capsule stays face-up the whole time, so a wet seal never touches another capsule or a tray. Tumble drying works for softgels; it doesn’t work for a seal that’s still setting.

Twelve stations, two of them doubled

Two stations separate capsules instead of one, which gives each capsule more time under vacuum at 16 bores. Two stations handle mixed filling instead of one, so you can drop in a heavier pellet load or two different components without slowing the line down.

Ideal Applications & Industries

Fish oil and omega-3

Oil fills wick into the shell if the seal isn’t right. The double-pass sealing wheel puts adhesive on twice — the first pass wets the seam, the second builds the film.

CoQ10 and fat-soluble vitamins

These cost more per kilo than most fills. The fiber detection skips dosing on any capsule that didn’t open, so you don’t pump expensive oil into a shell that’s heading for the reject bin.

Botanical extracts and oil-based blends

You can run gelatin one week and vegetable caps the next on the same machine. Tell us which shell you’re using — it changes how we set the separation station and the sealing temperature.

Combination supplements

A liquid plus a pellet or mini-tablet in the same capsule, kept physically apart. Two mixing stations load it at full speed instead of slowing the index. Send us both components and we’ll tell you if it runs.

What changing over actually involves

Parts to Replace

Adjustment Points

Changeover Time

Same capsule, different dose

Type the new fill volume on the screen. Nothing comes apart

15–30 minutes

Same capsule, different product

Ceramic pumps and material hopper have to be cleaned. No exceptions

15–30 minutes+ your cleaning time

Different capsule size

Upper and lower molds, transfer tray and drying molds all change

15–30 minutes

Quick to take apart where it counts. The drying molds hang free rather than being bolted in, so they come off quickly for a size change or cleaning.

Cleaning is part of the stop. Between products, the ceramic pumps and material hopper must be cleaned. Budget that time — it’s usually longer than the mechanical change.

One thing to teach your operators. The ceramic rods and plugs are lapped in matched pairs. Swap one between pumps and the fit is gone for good. Sixteen pumps means sixteen pairs that look identical. It’s in the manual and we cover it in training.

Three things to check before you buy any liquid capsule line

01

Accuracy

Your label says 500 mg. The machine has to put 500 mg in, every capsule, all shift. Ask any supplier what their fill tolerance is and how it's measured. Ours is ±2%, and we run your product at factory acceptance testing before the machine ships.

02

The manual

Your operators need to run this without calling China. Ask to see the English manual before you order — not a translated parts list, an actual operating manual with the maintenance schedule in it.

03

Installation and training

A machine that arrives and sits is not cheaper than one that arrives and runs. We install it, commission it, and train your operators on your product.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Fill Before You Order

Send us a sample of your fill and tell us your shell type. We run it on the line, seal and dry it, and send you the capsules and the fill weight figures before you order.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Deep Dive FAQ

How much does the NYF-1000 cost?

Price depends on capsule sizes, whether you need the dust extraction unit, and your electrical configuration. Send us your product, target output and capsule size and we’ll quote within 24 business hours. Most quotes include a free layout drawing.

How long is the lead time?

It depends on the configuration and our build schedule. We confirm the lead time in writing in your quote, before you pay a deposit.

Can it run my product?

If it’s a solution, suspension, microemulsion or a hot-melt fill, most likely yes. Very thin water-based fills can wick into the shell before the seal sets. Send us a sample and we’ll test it.

Does it work on US 60Hz power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

How long does a changeover take?

It depends what you’re changing. A dose change on the same capsule is set on the touchscreen. A capsule size change means changing the upper and lower molds, the transfer tray and the drying molds. Cleaning between products adds to that — budget for it. The changeover table above shows each case.

Does it include installation, training and spare parts?

Installation and operator training are available, and what’s included is listed in your quote. A commissioning spare parts kit ships with the machine, listed and priced in your quote before you sign.

Do your machines meet US electrical certification requirements?

Tell us which certification your site or your insurer requires. Our factory confirms in writing what the machine meets before production starts.

How much floor space do I need?

The machine is 4,100 × 1,300 × 2,100 mm. Add clearance on both sides for service access — the drying section needs to be reachable. Send us your room dimensions and we’ll draw a layout for free.

What is combination filling and do I need it?

It means putting two forms into one hard capsule — most often a liquid plus pellets or a mini-tablet — so ingredients that shouldn’t mix stay apart until the capsule dissolves. You need it if your formula has an ingredient that doesn’t dissolve or stay stable in the oil. Send us both components and we’ll tell you if it runs.

Customers Also Interested In...

Send us your product — we'll send back a configuration

Tell us what you’re filling, what capsule size and how much you need per month. We’ll come back with a machine recommendation, a layout drawing and a price. If the NYF-1000 isn’t the right size for you, we’ll say so.

Send your room dimensions and we’ll draw a free layout showing where the line goes and how much clearance you need.

Scroll to Top