NF-120 Automatic Tube Filling and Sealing Machine
Twin-station tube filling, 80 to 120 tubes a minute
Two tubes are filled and sealed at every index, which is how this machine reaches 120 tubes a minute without running the mechanics any harder. Tubes feed from a large magazine, each one is lifted so the nozzle fills from the bottom up, and the nozzle blows off and cuts off the product before the tube moves on. Hot-air sealing, lot coding and tail trimming follow in line.
1. Output: 80 to 120 tubes a minute, twin station
2. Fill: 3 to 250 ml, within ±1%
3. Tubes: plastic and laminated, Ø13–50 mm, 50–250 mm long
4. Two no-tube-no-fill checks: independent, so an empty holder never gets a dose
Is the NF-120 the right size for you?
✓ Yes, if…
- You need 80 to 120 tubes a minute
- Your tubes are plastic or laminated
- You're linking the filler to a cartoner or shrink wrapper downstream
- You have three-phase power and room for a machine this size
✕ Buy something else if…
- You need under 75 a minute → the NF-80 does the job with a single station and less floor
- Your tubes are aluminum → the NF-80M fills aluminum tubes
- You don't have three-phase power → the semi-automatic NF-30 runs on single phase
Twin Station, Two Tubes per Index
Two tubes move into position at every index and are filled and sealed together. That’s how the output reaches 120 a minute while each station still works at a steady pace.
Filled from the Bottom Up
Each tube is lifted so the nozzle starts near the bottom, then lowered as it fills. The product doesn’t drop through air into the tube, which is what causes bubbles and splashing onto the seal area.
Blow-Off and Cut-Off at the Nozzle
When the dose is in, the tube pauses while the nozzle blows off and cuts off the product. No drip, no thread of product across the seal. The nozzle connects with a quick-release fitting, so it comes off for cleaning without leaving product behind.
Two Independent No-Tube-No-Fill Checks
Two separate sensing systems check for a tube before each dose. If either finds an empty holder, the filler doesn’t fire.
Fill Volume Fine-Tuned on the Touchscreen
Density varies a little from batch to batch, and so does the weight of a fixed volume. The fill can be trimmed from the touchscreen to bring it back on target, without stopping to adjust the pump by hand.
Technical specification
| Parameter | NF-120 |
| Output | 80–120 tubes/min, twin station |
| Tubes | Plastic and laminated |
| Tube diameter | Ø13–50 mm |
| Tube length | 50–250 mm |
| Fill | 3–250 ml |
| Accuracy | ±1% |
| Sealing | Hot air, 3 kW × 2 |
| Main motor | 2.2 kW |
| Speed control | Inverter |
| Power supply | Three phase, 60 Hz. Built to your U.S. supply; we confirm the voltage with your quote |
| Compressed air | 0.5–0.6 MPa, 2 m³/min |
| Controls | Siemens PLC, inverter and touchscreen; encoder; color-mark sensor |
| Contact parts | 316L stainless steel |
| Dimensions | 2,350 × 1,300 × 2,400 mm |
| Weight | 1,400 kg |
| Floor space | About 4 m² for the machine, 20 m² working area |
| Options | Heated hoppers (2 kW × 2), stirrers (0.18 kW × 2), double-sided coding |
Model comparison
Model | Operation | Tubes | Speed | Fill | Power |
NF-30 / NF-30M | Semi-automatic | Plastic / aluminum | 10–30/min | 5–250 ml | Single phase |
NF-60A | Automatic | Plastic, laminated | up to 60/min | 5–250 ml | Three phase |
NF-80 | Automatic | Plastic, laminated | 50–75/min | 5–250 ml | Three phase |
NF-100 | Automatic | Plastic and aluminum | 80–100/min | 5–180 ml | Three phase |
NF-120 | Automatic, twin station | Plastic and aluminum | 80–120/min | 5–250 ml | Three phase |
Industry Applications
Typical OTC products in U.S. supplement and OTC plants:
Fluoride Toothpaste at Volume
One or two toothpaste SKUs running across shifts, where 120 tubes a minute pays back. The tube is lifted so the nozzle fills from the bottom up, which keeps air out of a thick paste.
Pain-Relief Gels and Creams
High-volume analgesic gels and creams in printed laminated tubes, where the print has to survive the seal every time.
Sunscreen Lotions
Regulated as OTC drugs in the U.S. Lotions and creams filled on two stations at once, with two independent no-tube-no-fill checks.
Boxed OTC Creams, Straight from the Filler
The filler linked to a cartoner and a shrink wrapper, so tubes go from filling to boxed without being handled.
What changing over involves
What changed | What you adjust | Roughly |
Different fill | Pump setting | 15–30 minutes |
Different tube diameter | Tube holders | 15–30 minutes |
Different product | Clean the hopper and pump | 15–30 minutes |
What to check before you buy
Your tube, not a sample tube
Plastic, laminated and aluminum tubes seal in different ways. Ask any supplier to run your tube, not one of theirs.
Plastic or aluminum — or both?
Many semi-automatic fillers seal only one kind of tube. If you run both, ask whether that's one machine or two.
Your power supply
This machine needs three-phase power. Only the semi-automatic NF-30 runs on single phase — check before you choose.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Tubes Before You Order
Send us a few of your empty tubes and a sample of your product. We need your tube to size the holders and set the sealer anyway, so we fill and seal them on the machine and send them back. You’ll see the seal, the code and whether the print still looks right after the heat — on your own tube and your own product, not a sample we chose.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
NF-120 Automatic Tube Filling & Sealing Machine Comprehensive Technical FAQ
Two tubes are indexed into position at the same time and filled and sealed together. Output doubles without the turntable or the pumps having to run twice as fast — each station works at the pace of a 60-a-minute machine.
Hot air is aimed at the inside of the tube tail, where the layers need to soften and fuse. A water chiller keeps the tube holders cool, so the heat stays at the seal instead of spreading toward the product.
Two independent sensing systems check for a tube before the filling station. If either finds an empty holder, the filler doesn’t fire for that cycle.
Each tube is lifted so the nozzle fills from near the bottom upward, which keeps air out and stops splashing. At the end of the dose the nozzle blows off and cuts off the product, so it breaks cleanly without a thread across the seal.
No. The NF-120 fills plastic and laminated tubes with hot-air sealing. For aluminum tubes, see the NF-80M.
Yes. The NF-120 can run on its own or be linked with an automatic cartoner and a shrink-wrapping machine to form a continuous line. Tell us which downstream machines you have and we’ll check their rates against the filler’s.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us an Empty Tube and a Sample
Two things decide which machine you need: whether your tubes are plastic, laminated or aluminum, because each is sealed differently, and how many you need a day. Tell us both and we’ll tell you whether a semi-automatic machine is enough.
Better still, send us a few empty tubes and a sample of your product. We’ll fill and seal them and send them back.
- Direct from our factory
- Lead time confirmed in your quote
- Installation and training available
- Spare parts listed in your quote