NF-30 Semi-Automatic Tube Filling and Sealing Machine

10 to 30 tubes a minute, on single-phase power — for small batches and new products

Filling tubes by hand is slow and every tube comes out a little different. This machine fills and seals them for you: an operator drops each empty tube into its holder, and the machine lines up the print, fills the tube, seals the tail and stamps the lot number. It runs on single-phase power, so it goes in without a new electrical supply. For plastic and laminated tubes; the NF-30M does the same job for aluminum tubes.

1. Output: 10 to 30 tubes a minute, loaded by hand

2. Fill: 5 to 250 ml per tube, within ±1%

3. Tubes: plastic and laminated, Ø13–50 mm, 50–210 mm long

4. Power: single phase. No three-phase supply needed

Is the NF-30 the right size for you?

✓ Yes, if…

✕ Buy something else if…

Hot Air on the Inside of the Tube

Plastic and laminated tubes are sealed with hot air blown onto the inside of the tube tail, then pressed flat The printed outside isn’t heated directly, so the artwork doesn’t scorch.

Print Lined Up Before Filling

A color-mark sensor and a stepper motor turn each tube until the printed eye-mark faces the right way, so every sealed tail lines up with the front of the tube.

Seal, Stamp and Trim in One Station

The tail is sealed, the lot number is stamped into the seal, and the end is trimmed at the same station — no second machine for coding.

Optional Heated, Stirred Hopper

A double-jacketed hopper keeps products that thicken as they cool — balms, waxes — at a fillable temperature. Available as an option.

Technical specification

Parameter

NF-30 (plastic, laminated)

NF-30M (aluminum)

Operation

Semi-automatic, tubes loaded by hand

Semi-automatic, tubes loaded by hand

Output

10–30 tubes/min

10–30 tubes/min

Fill

5–250 ml

5–180 ml

Accuracy

±1%

±1%

Tube diameter

Ø13–50 mm

Ø13–35 mm

Tube length

50–210 mm

50–180 mm

Sealing

Hot air, pressed flat

Mechanical folding

Controls

Push buttons; touchscreen optional

Touchscreen

Motor

0.75 kW

1 kW

Power supply

Single phase, 60 Hz. Built to your U.S. supply; we confirm the voltage with your quote

Same

Compressed air

Above 0.4 MPa

Above 0.4 MPa

Dimensions

1,100 × 800 × 1,600 mm

1,100 × 800 × 1,600 mm

Weight

280 kg

280 kg

Options

Heated, stirred hopper; water chiller; touchscreen; finished-tube conveyor

Heated, stirred hopper

Model comparison

Model

Operation

Tubes

Speed

Fill

Power

NF-30 / NF-30M

Semi-automatic

Plastic / aluminum

10–30/min

5–250 ml

Single phase

NF-60A

Automatic

Plastic, laminated

up to 60/min

5–250 ml

Three phase

NF-80

Automatic

Plastic, laminated

50–75/min

5–250 ml

Three phase

NF-100

Automatic

Plastic and aluminum

80–100/min

5–180 ml

Three phase

NF-120

Automatic, twin station

Plastic and aluminum

80–120/min

5–250 ml

Three phase

Industry Applications

Typical OTC products in U.S. supplement and OTC plants:

Hydrocortisone and Anti-Itch Creams

Short runs of OTC anti-itch creams in plastic or laminated tubes, filled and sealed the same way every time before volume justifies an automatic line.

Zinc Oxide and Petrolatum Ointments

Thick ointments that stiffen as they cool. The optional heated, stirred hopper keeps them fillable through the run.

Medicated Lip Ointments

Small tubes from Ø13 mm, at volumes too low for an automatic machine.

Antibiotic Ointments in Aluminum Tubes

First-aid ointments that need a full barrier against air and light, folded rather than heat-sealed on the NF-30M.

What changing over involves

What changed

What you adjust

Roughly

Different fill

Pump setting

15–30 minutes

Different tube diameter

Tube holders

15–30 minutes

Different product

Clean the hopper and pump

15–30 minutes

What to check before you buy

01

Your tube, not a sample tube

Plastic, laminated and aluminum tubes seal in different ways. Ask any supplier to run your tube, not one of theirs.

02

Plastic or aluminum — or both?

Many semi-automatic fillers seal only one kind of tube. If you run both, ask whether that's one machine or two.

03

Your power supply

This machine runs on single-phase power. The automatic models need three-phase — check before you choose.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Tubes Before You Order

Send us a few of your empty tubes and a sample of your product. We need your tube to size the holders and set the sealer anyway, so we fill and seal them on the machine and send them back. You’ll see the seal, the code and whether the print still looks right after the heat — on your own tube and your own product, not a sample we chose.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

NF-30 Tube Filling Machine Comprehensive Technical FAQ

Why choose a semi-automatic filler for R&D and short runs?

Because the format is still changing. The NF-30 takes little floor, wastes little product when you prime it, and changes tube size by swapping the tube holders. It runs on single-phase power, so it goes into a development room without a new electrical supply.

Can the NF-30 fill both plastic and aluminum tubes?

Not on the same machine. Plastic and laminated tubes are sealed with hot air; aluminum tubes are folded. The NF-30 handles plastic and laminated tubes, and the NF-30M handles aluminum.

How is the manual tube loading process optimized on the NF-30 to maintain a continuous pace?

The operator drops each empty tube into its holder, and the machine does the rest: it lines up the print, fills the tube, seals the tail, stamps the lot number and trims the end. One operator keeps up 10 to 30 tubes a minute.

How does the NF-30 prevent high-viscosity creams from dripping or forming tails that ruin the tube seal?

Thick creams and ointments tend to leave a thread of product behind when the nozzle lifts away, and that thread lands where the seal will be. The NF-30 uses a cut-off nozzle that blows off and cuts off the product at the end of each dose, so the break is clean and the seal area stays clear.

Is the product hopper heated, and how do you handle formulas that require continuous agitation?

The standard hopper is single-walled. For ointments and balms that thicken as they cool, a double-jacketed heated hopper with a stirrer is available as an option, to keep the product at a fillable temperature through the run.

What air compressor capacity is required to support the continuous operation of the NF-30?

Since the sealing jaws, hot-air nozzle alignment, and dosing valve cut-offs are entirely driven by pneumatic actuators, the NF-30 requires a reliable source of clean, dry compressed air. The system requires an operating pressure above 0.4 MPa. We recommend pairing the machine with a standard, low-noise oil-water separator air compressor to safeguard the internal pneumatic seals.

Does it need three-phase power?

No. It runs on single-phase power — the only machine in our tube range that does. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote. The automatic models need three phase.

Does it run on US power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send Us an Empty Tube and a Sample

Two things decide which machine you need: whether your tubes are plastic, laminated or aluminum, because each is sealed differently, and how many you need a day. Tell us both and we’ll tell you whether a semi-automatic machine is enough.

Better still, send us a few empty tubes and a sample of your product. We’ll fill and seal them and send them back.

  • Direct from our factory

  • Lead time confirmed in your quote

  • Installation and training available

  • Spare parts listed in your quote

Scroll to Top