APKZRJ Bottom Homogenizer Vacuum Emulsifying Mixer
Vacuum emulsifier with the homogenizer at the base of the vessel — for creams with powders that settle
Some creams carry powders that sink before they can be mixed in — zinc oxide, calamine, heavy thickeners. This machine puts the homogenizer at the bottom of the vessel, where those powders settle, so they’re drawn into the shear zone rather than left on the floor of the tank. The phases are drawn in and mixed under vacuum, the same as on our lid-lift model.
1. Homogenizer position: at the base of the vessel, where heavy powders settle
2. Capacity: 50 to 1,000 liters per batch
3. Homogenizer: 1.1 to 11 kW, 0 to 3,000 rpm
4. Mixed under vacuum: phases drawn in and air pulled out as the batch mixes
Is the APKZRJ-B the right size for you?
✓ This is a fit if…
- Your formula includes powders that settle — zinc oxide, calamine, heavy thickeners
- You make OTC creams, pastes or lotions under vacuum
- Your batches are between 50 and 1,000 liters
✕ Buy something else if…
- Your powders are light and float on the surface → the top-homogenizer APKZRJ draws them down from above
- Your formula has little or no powder → a standard lotion or cream is handled just as well by the APKZRJ
- Your batches are over 1,000 liters → the APKZRJ goes up to 2,000 liters
- Your ceiling can't take a lid-lift machine → the fixed-lid APKZRJ-F needs no clearance above the vessel
Homogenizer at the Base
The homogenizer sits at the lowest point of the vessel, where heavy powders collect. Zinc oxide, calamine and other mineral powders are drawn into the shear zone as they settle, instead of building up on the floor of the tank.
Mixed Under Vacuum
The phases are drawn into the vessel under vacuum, and air is pulled out of the product while it mixes. The finished cream comes out without trapped bubbles.
The Seal Below the Vessel
On a bottom homogenizer, the drive shaft comes up through the floor of the vessel, so the seal around it sits under the full weight of the batch. That seal is the part to ask about first — how it’s built, how it’s cooled and how often it needs replacing.
Discharged from the Bottom
The finished product leaves through a valve at the base of the vessel.
Slow Mixer, Heated Jacket
A slow mixer keeps the whole batch turning while the homogenizer works at the base, and the jacketed vessel heats electrically or by steam.
Technical specification
Parameter | APKZRJ-B50 | APKZRJ-B100 | APKZRJ-B500 | APKZRJ-B1000 |
Working capacity | 50 L | 100 L | 500 L | 1,000 L |
Homogenizer motor | 3 kW | 3 kW | 7.5 kW | 11 kW |
Homogenizer speed | 0–3,000 rpm | 0–3,000 rpm | 0–3,000 rpm | 0–3,000 rpm |
Mixer motor | 0.75 kW | 1.5 kW | 2.2 kW | 3.7 kW |
Mixer speed | 0–60 rpm | 0–60 rpm | 0–60 rpm | 0–60 rpm |
Dimensions | 2,750 × 2,100 × 1,900 mm | 2,800 × 2,150 × 2,100 mm | 3,800 × 2,800 × 2,700 mm | 3,900 × 3,400 × 3,150 mm |
Height, lid raised | 2,600 mm | 2,800 mm | 3,950 mm | 4,550 mm |
Heating | Electric (water jacket) or steam | Electric (water jacket) or steam | Electric (water jacket) or steam | Electric (water jacket) or steam |
Dimensions and motor ratings for each size are confirmed with your quotation.
Model comparison
Model | Type | Capacity | Homogenizer | Height, lid raised | Best for |
APKZRJ | Lid-lift, top homogenizer | 10–2,000 L | 1.1–22 kW, 0–3,500 rpm | 1.7–4.55 m | Creams, lotions and gels; light powders that float |
APKZRJ-B | Bottom homogenizer | 50–1,000 L | 1.1–22 kW, 0–3,500 rpm | 1.3–3.6 m | Formulas with heavy powders that settle |
APKZRJ-F | Fixed lid | 100–1,000 L | 1.1–22 kW, 0–3,500 rpm | 1.3–3.6 m | Rooms with limited headroom |
APKYGJ | Toothpaste mixer | 300–2,000 L | 5–22 kW, 0–3,500 rpm | 3.55–4.55 m | Toothpaste and tooth gels |
Choose by where your powders end up. Heavy powders that settle suit a homogenizer at the base. Light powders that float suit one from above — the APKZRJ.
Industry Applications
Zinc Oxide Diaper-Rash Creams
A heavy load of zinc oxide that sinks fast. The homogenizer at the base catches it as it settles.
Calamine Lotion
A lotion full of mineral powder that won’t stay suspended on its own, mixed from the bottom up.
Mineral Sunscreen Creams
Regulated as OTC drugs in the U.S. Zinc oxide creams where the powder has to be evenly dispersed through the whole batch.
Switching Products
There are no change parts on a vacuum emulsifier. Switching from one product to the next means emptying the vessel, cleaning it and setting new temperatures and speeds.
What changed | What you do | Roughly |
Same product, next batch | Discharge, rinse through the CIP port | 15–30 minutes |
Different product | Discharge, clean through the CIP port, lift the lid to inspect | 15–30 minutes |
Different heating temperature | Set on the touchscreen | Seconds |
Different mixing speed | Set on the touchscreen | Seconds |
The vacuum is broken through a filtered valve before the product is discharged and before the lid lifts — the machine won’t let you do either under vacuum.
What to Check Before You Buy
Your batch size, not the vessel size
A vessel is never filled to the top. Ask for the working capacity and size the machine to your usual batch, not your largest one.
How the powder goes in
Toothpaste is mostly powder. Ask whether the powder is drawn in under the liquid surface or poured onto it — that decides whether you get lumps.
How you'll heat it
Electric heating works anywhere. Steam is faster on large vessels but needs a steam supply. Confirm which you have, and confirm your voltage before the machine is built.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Look at Your Formula First
Send us your formula, or just what you’re making and how big your batches are, and we’ll tell you which model and which size suits it before we quote.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Questions About the APKZRJ-B
It depends on your powders. Light powders that float on the surface, such as many thickeners, are best drawn down by a homogenizer working from above. Heavy powders that sink, such as zinc oxide and calamine, are best caught by a homogenizer at the base. Send us your formula and we’ll tell you which suits it.
Formulas where the powder is heavier than the cream around it: zinc oxide diaper-rash creams, calamine lotion and mineral sunscreen creams. If your formula has little or no powder, the top-homogenizer APKZRJ will do the same job.
Yes. A slow mixer keeps the whole batch turning while the homogenizer works at the base, so the product near the wall doesn’t sit still. Send us your formula if it’s especially thick, and we’ll confirm before you order.
Two things. It draws the ingredients into the vessel, and it pulls air out of the product while it mixes, so the finished cream comes out smooth and free of trapped bubbles.
On a bottom homogenizer, the drive shaft comes up through the floor of the vessel, so the seal around it carries the weight of the whole batch. Ask how it’s built, how it’s cooled and how often it needs replacing — and ask for the price of a replacement seal in your quote.
Four sizes: 50, 100, 500 and 1,000 litres. For batches up to 2,000 litres, see the top-homogenizer APKZRJ.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us Your Formula — or Just Your Batch Size
Three things decide which emulsifier you need. Your batch size decides the capacity. Your ceiling height decides lid-lift or fixed lid — a lid-lift model needs room above the vessel for the lid to rise. And if your formula carries a heavy powder load that settles, that decides where the homogenizer should sit.
Tell us those three and what you’re making, and we’ll point you to the right model. If you can share your formula, even better — we’ll look at it before we quote.
- Reply within one business day
- A model matched to your batch, ceiling and formula
- Your formulation stays with us
No sales calls — we reply by email or WhatsApp, whichever you gave us.