How Much Floor Space Does Your Cartoning Line Need?
You’ve measured the room and checked the machine’s length and width. Now let’s follow the product: where it arrives, who adds supplies, which machine doors need to open, and where finished cartons go. That helps us see the space your full setup needs.

AIPAK’s cartoning line in a factory
Plan the cartoner, infeed, loading and restocking space, service access, and downstream handoff together. Then check them against your room.
The space depends on your configuration. We’ll start with the room’s length, width, clear height, doors, columns, and existing equipment, then review the areas you’ll need to use.
Check the cartoner, infeed, and carton handoff alongside operator access, service space, and site obstacles. Positions explain what to review; they are not a recommended layout.
01 / MAP OUT THE SPACE YOU NEED
What needs room around the cartoner?
We’ll put the infeed, cartoner, carton handoff, and operating and service areas on one drawing, then check them against your room. The machine’s dimensions are one part of that review. The full space requirement depends on the configuration and conditions at your site.
The cartoner itself

Check the outline and proposed position of the specific model. Make sure you know which parts its dimension drawing includes.
The equipment around it

Include product supply, arranging or hand-loading sections, and the handoff after cartons leave the machine.
Space to use the setup

Look at where people operate, how they add products and cartons, how doors open, and how service points are reached.
You may already have an open area set aside. Let’s follow your product from where it arrives, through any preparation steps, to where cartons leave. That makes it easier to see what belongs in the layout.

The room’s shape and door and column positions also affect the arrangement. Adding up the area taken by each machine helps describe the equipment involved. To see whether the setup fits, we need to look at the site information and configuration drawing together.
You can start with: “We can use this area, these machines have to stay where they are, and products arrive from this direction.” That gives us more to work with than a total floor-area figure alone.
02 / COMPARE THE MACHINE WITH THE ROOM
Horizontal or vertical: how do you compare the space?
If you’re comparing horizontal and vertical cartoners, we’ll first check the product, carton, loading requirements, and infeed conditions. Then we can look at the length, width, and height of suitable setups. Room dimensions, clear height, and local obstacles all need to be checked against the actual model and packing plan.


AIPAK’s horizontal and vertical cartoners
If your room is narrow, or beams and pipes run overhead, mark those constraints on the site plan. We’ll compare them with the candidate setup’s infeed, outfeed, operating areas, and service requirements to see where conflicts need attention.
Show us the usable space, along with the total area.
Match length, width, clear height, and the positions of doors, columns, beams, and pipes to the area you can actually use. This concept sets no standard dimensions.

- Start with the packing job: Match the product format, items per carton, and carton requirements to the candidate setup.
- Compare the same scope: Make clear which infeed, outfeed, and supporting equipment each option includes before comparing dimensions.
- Check it against your site: Add doors, columns, beams, pipes, clear height, and fixed equipment to the review. List the points that restrict the layout.
If you already have two dimension drawings, send both and tell us what each includes. We can use the same packing job to work through what still needs to be confirmed.
03 / FOLLOW THE PRODUCT INTO THE MACHINE
Automatic feeding or hand loading: what needs to fit?

Automatic feeding and hand loading process
How you feed products affects the length and arrangement of the full setup. We need to see how products arrive, how they’re arranged or grouped, who loads them, and how supplies reach the loading area. Once the infeed configuration is clear, we can place it in the layout alongside the cartoner.
Include arranging, loading, and restocking in the infeed plan.
Automatic feeding and hand loading involve different activities to review. A longer hand-loading section can be discussed for the project. These concepts do not compare actual lengths or capacities.
You’re planning automatic feeding
Show us how products arrive. We’ll check the arranging, orienting, or grouping steps needed, along with the configuration, handoff, and operating and service space.
You’re planning to load by hand
Tell us where people will load, where they’ll get products, and how supplies will be replenished. We can discuss whether a longer loading section makes sense for the job, staffing plan, and room.
Even the same type of product can arrive in different ways. Products already facing the right direction ask something different of the infeed than products that still need arranging. We’ll base the review on how yours actually arrive.

If several products will share the line, tell us about each carton, items per carton, and feeding method. Let’s list the jobs you need to run before discussing how manual and automatic feeding might be arranged.
04 / LOOK AT HOW PEOPLE AND PARTS MOVE
Can you open the doors, add supplies, and reach service points?

Once the equipment position is proposed, we’ll check the model’s door-opening, loading, and maintenance instructions. Can people reach the points they need to use? Is there a route to remove and move parts? Those spaces need to be reviewed with neighboring equipment and fixed obstacles in place.
Allow for the movements people and parts need to make.
Check door opening, service access, and part removal separately. These are generic activity symbols, not a specific machine’s design or required clearances.
| What you'll do | What we'll check |
|---|---|
| Operate, add cartons, and replenish products | Operator positions, how cartons and products arrive, and how material handling passes through the area. |
| Open guards or reach service points | The actual door movement and access direction, plus any doors, columns, or nearby machines that could block the activity. |
| Remove and move parts | The removal direction, working space, and transfer route stated in the maintenance instructions. |
| Move the equipment into the room | The entrance, turns along the route, and fixed obstacles, checked against the equipment move-in plan. |
An area that looks open during production may also be needed when a door opens or maintenance starts. We’ll mark the activities separately, then use your operating plan to check where space can be shared and where more room is needed.

If entrances, corners, or existing equipment create obvious restrictions, take a few photos for us. Both the move-in route and the installed position are worth reviewing while the layout is being planned.
05 / INCLUDE WHAT HAPPENS AFTER CARTONING
What happens after the carton leaves the machine?

Parts of AIPAK’s cartoning line
Tell us where finished cartons need to go. We’ll discuss coding, checkweighing, case packing, or other steps based on your packaging needs and existing equipment. Make clear what needs to be added and how each part will hand off to the next within the scope of this project.
Where do your finished cartons go next?
Coding, checkweighing, and case packing are examples to review as needed. The dotted lines do not define a process sequence. List existing equipment separately from anything to be added.
If you already have downstream equipment, we’ll start with its actual position, infeed direction, and handoff conditions. If you plan to add equipment, first list the steps it needs to perform. Then we can discuss equipment and conveyor arrangements.

Downstream equipment also needs space for operating, service, and finished-carton handling. We’ll bring those needs back into the full layout and review them alongside the cartoner’s outfeed.
Equipment you already have
Mark its position and direction, and tell us what can move. Photos, a site plan, or existing equipment dimension drawings all help.
What you plan to add
Start with the work it needs to do and where finished cartons should go. We’ll confirm the equipment and handoff work included in the specific solution.
06 / TURN THE QUESTION INTO SITE DETAILS
What can you send us to start the layout discussion?
Start with the site information and packing ideas you already have. Room photos, a hand sketch, equipment drawings, and product or sample-carton details can all get the conversation started. Before confirming a layout, we’ll work through accurate dimensions, the complete configuration, and site constraints together.
Start by showing us your space. Details can follow.
Site photos, a hand sketch, and product details can start the discussion. Mark any dimensions you’re unsure of. The final layout still needs accurate site information and the actual configuration drawing.
| What it's about | What you can tell us first | What we'll use it to check |
|---|---|---|
| The room and usable area | Length, width, clear height, and the positions of doors, columns, and existing equipment. Mark anything still unknown. | The actual usable boundary against the proposed configuration. |
| Your product and carton | What you're packing, items per carton, and the product range. Photos, samples, or drawings are all useful. | The packing format and candidate cartoner. |
| Infeed and production target | How products arrive, whether you'll load by hand or automatically, and the output you need. | How the infeed section and operating plan fit the cartoning job. |
| Downstream equipment and site limits | What you need to connect, what cannot move, and any entrance or corner restrictions. | Carton handoff, service activities, and the equipment move-in plan. |
If you don’t have a room drawing yet, start with a sketch and mark the positions you know. If the carton hasn’t been decided, we can also help you work through carton design and the cartoning plan before reviewing the configuration and site conditions.

You can start with: “I want to carton this product. This is the area we can use, and products arrive from here. What I’m unsure about is…” Tell us where you’re stuck, and we’ll work through the next details together.
Questions you may have
A few more space questions we can work through together.
Yes. Tell us the room’s rough shape, the equipment already there, and where you’d like the cartoner to go. As we work through the arrangement, we can fill in length, width, clear height, doors, columns, and other site details.
We also need to review product feeding, operator access, restocking, door opening, maintenance, and downstream handoff. The position and space for each part need to be checked against the actual configuration drawing.
Start with the product, carton, and feeding needs. Then compare suitable models and full configurations. Room dimensions and clear height are part of that choice and need to be reviewed alongside the equipment.
We can discuss it for your project. We’ll look at how products are loaded, your staffing plan, the job’s target, and the space available to see whether extra loading length is needed and how the proposed setup would be arranged.
That depends on your needs and the scope you’re buying. List existing equipment positions and directions, anything you plan to add, and how finished cartons will be handed off. Then we can review the full layout.
Yes. Send photos, video, or a hand sketch, or simply describe your space. Mark known dimensions and fill in anything uncertain later. Final layout confirmation still needs accurate site information and the actual configuration.
A room photo, a short infeed video, or a hand sketch can get us started. If you don’t have any files, describe your product and idea. Tell us what you’re unsure about, and we’ll work out which details to review next.
You have photos or video
Show the usable area, existing equipment, and how products arrive.
You have drawings or a hand sketch
Mark known dimensions, doors, columns, and equipment that has to stay in place.
You don’t have files yet
Describe your product and space. We can discuss carton design, too.
A short description and one contact method are enough to start. Accurate dimensions and other details can follow later.
You can start with: “I’d like to see whether this cartoning setup will fit in our current room.”
Table of Contents
Tell us about your product, feeding method, and usable area. Send photos if you have them. A description is fine if you don’t have drawings.