APKZL-60 Automatic Straight Tube Labeling Machine
Horizontal roller labelling for tubes Ø15–30 mm, with batch coding built in
A standing tube is tall, light and easy to knock over. This machine lays it down on rollers and rolls the label on along its length, so nothing wobbles and the label lands parallel every time. Batch coding is part of the machine, not an add-on.
1. Speed: 60 tubes a minute, matched to the fastest filler in the range
2. Tube size: Ø15 to 30 mm, 80 to 145 mm long
3. Coding built in: lot and date stamped onto the label as it feeds
4. Label roll: 75 mm core, up to 300 mm outside diameter
Is this the right machine for you?
✓ Yes, if…
- You're labelling straight tubes or bobbin bottles, Ø15 to 30 mm
- Your tubes are 80 to 145 mm long
- You need up to 60 tubes a minute
- You want lot and date coded in the same pass, not on a separate machine
- Your label rolls have a 75 mm core and stay under 300 mm outside diameter
✕ Buy something else if…
- Your containers are round bottles, not tubes → a standard wrap-around labeller handles those, and costs less. This machine is built around a tube lying on its side
- Your tube is over Ø30 mm or longer than 145 mm → outside the range. Send us the dimensions and we'll tell you honestly
- You need more than 60 tubes a minute → nothing in our tube range runs faster, so the labeller would become your line speed
- Your label wraps only part of the tube, with registration to a printed panel → tell us first
Laid Down, Not Stood Up
A standing tube is tall, light and top-heavy, and a vertical labeller has to hold it steady while the label wraps. This machine lays the tube on rollers along its whole length and rolls the label on. Nothing has to hold it upright, so nothing tips.
Takes Tubes Straight From the Filler
Capped tubes come off the APK-40B or APK-60 in sequence and go onto this machine’s track without anyone handling them. It runs at 60 tubes a minute — the same rate as the fastest filler, so it doesn’t become the station that holds the line up.
Stepper Drive, Fewer Wear Parts
A stepper motor and controller replace the clutch and gear train a mechanical labeller uses to pace the label web. Fewer moving parts to wear, and label position is set on the screen rather than by adjusting a linkage.
Batch Coding as the Tube Passes
A colour-mark sensor tracks each label as it feeds, and the coder stamps the lot and date onto it in the same pass. No second station, and no tube leaving without a code.
Technical specification
Specification | APKZL-60 | What it means for you |
Speed | 60 tubes/min | Matched to the APK-60, the fastest filler in the range |
Tube diameter | Ø15–30 mm | Guide rails adjust on handwheels |
Tube length | 80–145 mm | — |
Drive | Stepper motor | Label position is set on the screen |
Batch coding | Built in, lot and date | Printed onto the label as it feeds |
Control | Siemens PLC and touchscreen | — |
Sensors | Fiber-optic tube detection and color-mark sensor | No tube, no label |
Label roll | 75 mm core, up to 300 mm outside diameter | — |
Power | 0.8 kW, 60 Hz | Built to your U.S. supply. We confirm the voltage with your quote |
Dimensions | 1,400 × 500 × 1,250 mm | — |
Weight | 320 kg | — |
Construction | SUS304 table cover, sandblasted aluminum base | — |
Model comparison
Model | Indexing | Speed | Power | Weight |
APK-40A | Pneumatic | 35–40 tubes/min | 1.2 kW | 420 kg |
APK-40B | Stepper + indexing disk | 35–40 tubes/min | 1.5 kW | 420 kg |
APK-60 | Stepper, with short-count rejection | 50–60 tubes/min | 2 kW | 1,000 kg |
APKZL-60 | Tube labeller | 60 tubes/min | 0.8 kW | 320 kg |
The APKZL-60 runs at 60 tubes a minute, so it keeps up with any filler above it in this table.
Production Applications
Effervescent tablet tubes
The format this machine was built around. Long, light tubes that won’t stand steady on a vertical labeller.
Supplement and vitamin tubes
Vitamin C, electrolytes and calcium in bobbin tubes, with lot and date coded as they pass.
Short runs across several tube sizes
Guide rails adjust on handwheels between Ø15 and 30 mm, so a tube change doesn’t need new tooling.
What changing over involves
What changed | What you adjust | Roughly |
Different tube diameter | Guide rails, on handwheels | A few minutes |
Different tube length | Guide rails, on handwheels | A few minutes |
New label | Load the roll and set the label position on the screen | A few minutes |
New lot or date | Change the code on the touchscreen | Under a minute |
No change parts to swap. Everything inside Ø15–30 mm and 80–145 mm is set by adjustment.
What to check before you buy
Your tube and your label, before the machine
Tube Ø15–30 mm and 80–145 mm long, label on a 75 mm core and no more than 300 mm across the roll. Ask any supplier to run your actual tube and label before you order.
What happens at an empty gap
A labeler that dispenses on a timer wastes a label every time a tube is missing. Ask whether it labels only when a tube is actually there.
Installation and training
Ask what's included and what costs extra.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Tubes and Labels Before You Order
Send us a few empty tubes and a roll of your label. We label and code them on the machine and send them back. You decide whether to talk quotes after that.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Questions About the APKZL-60
Standard round bottle labelers hold containers vertically, which causes long, lightweight plastic or aluminum effervescent tubes to wobble or tip over at high speeds. The APKZL-60 utilizes a specialized horizontal roller conveying bed that cradles the tube completely flat along its side. Nothing has to hold the tube upright, so the label goes on straight.
A fiber-optic sensor at the infeed checks for a tube. If there isn’t one, the PLC holds the stepper and no label is dispensed. A label only goes out when a tube is in position, so you don’t lose labels to empty gaps or find them stuck to the rollers.
Yes. The coder is synced to the color-mark sensor, so it prints on each label as it feeds: lot number, manufacturing date and expiration date. The print position is adjusted on the touchscreen to line up with your label design.
Not complex. Your operator turns the handwheels to set the guide rails to the new tube. Anything from Ø15 to 30 mm and 80 to 145 mm long runs without change parts.
A 75 mm core, and no more than 300 mm across the outside of the roll.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us Your Tubes and a Label
Two things decide whether this machine suits you: your tube has to be Ø15 to 30 mm and 80 to 145 mm long, and your label roll has to fit a 75 mm core and stay under 300 mm across.
Send us a few empty tubes and a roll of your label. We’ll label and code them on the machine and send them back, so you can check the label position and the print before you order.
- Reply within one business day
- Your tubes and labels run on the machine before you order
- Your formula and specs stay with us