APC-T1 Round Bottle Labeling Machine

The APC-T1 wraps a self-adhesive label around round bottles as they pass through, at 20 to 120 bottles per minute. It’s the last station on a counting and bottling line, and the one your customer actually sees. If your labels go on crooked or wrinkled, this is what fixes it.

  • 20 to 120 bottles per minute — keeps pace with any counting line up to 120 bpm
  • Round bottles of any size in the range — no change parts to swap between diameters
  • Pre-feed label system — the label is staged before it’s applied, so it lands flat and square

Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote

Is the APC-T1 the right labeler for your line?

✓ This is a fit if…

✕ Look elsewhere if…

Technical specification

Parameter

Value

What this means for you

Labeling speed

20 – 120 bottles / min

Match this to your capper and sealer, not your counter

Container type

Round bottles

Square or flat bottles need the APC-T2

Container diameter range

 15 – 130 mm

Your bottle has to fall inside this

Label width range

15 – 130 mm

Check against your artwork

Label roll core / outer diameter

76 mm (3 inch)

Confirm with your label printer before you order

Labeling accuracy

±1 mm (Depending on bottle and label squareness)

How square the label lands, bottle after bottle

Coder

Optional: ribbon date coder or thermal transfer printer (TTO)

Prints the batch number and dates on the label as it’s fed

Power

0.15 kW, 60 Hz

Built to your U.S. supply. We confirm the voltage with your quote

Compressed air

0.4 MPa, 0.2 m³/h

Small demand — most existing compressors cover it

Machine dimensions

2000 × 700 × 1650 mm

Add conveyor length either side

Machine weight

280 kg

—

 

The 2000 mm length is the machine itself. Allow conveyor run-in and run-out on both sides so bottles are travelling straight before they reach the applicator.

Model comparison

Model

Speed

Containers

Best for…

 

APC-T1

20–120 btl/min

Round bottles

One wrap-around label on a round bottle

You are here

APC-T2

20–120 btl/min

Square, flat and round bottles

Two, three or four-sided labeling on square containers

View →

APC-T3

20–120 pcs/min

Flat surfaces

Labeling the top face of boxes, lids and trays

View →

APC-T4

100–200 btl/min

Ampoules, oral liquid vials

Small vials handled horizontally at higher speed

View →

All four use the same pre-feed label system and tensioned web. What changes is how the container is presented to the applicator.

Pre-feed label system

The label is staged and held before the bottle arrives, rather than being pulled from the roll at the moment of application. That’s what keeps label position repeatable at speed.

You see the difference at the end of a shift, not at the start. A machine that pulls labels on demand drifts as the roll diameter shrinks. A pre-feed system doesn’t.

Tensioned web

The label web runs under controlled tension between the roll and the applicator. Two things depend on it: the coder prints cleanly because the web isn’t slack, and every label is fed to the same length.

Slack web is the usual cause of smeared batch codes and labels that start at slightly different points down a run.

Roll-on application matched to the bottle

The roll-on mechanism is configured to the shape of your bottle. A tall narrow bottle and a short wide one don’t press the same way, and using one arrangement for both is how you get wrinkles at the leading edge.

Tell us your bottle dimensions and we set this up before the machine ships.

Ideal Applications & Industries

Supplement bottles with full-wrap labels

A full-circumference label has to meet itself with no overlap gap and no wrinkle. Most complaints about “the label looks cheap” come down to the leading and trailing edge, not the artwork.

Bottles with a batch code and expiry date

The coder prints on the label as it’s fed, before it reaches the bottle. The web tension is what keeps the print legible — a slack web smears the code, and a smeared code is a rejected batch.

Small dropper and tincture bottles

A 30 ml bottle has very little label real estate and very little tolerance. The label has to start and finish in the right place because there’s nowhere for the error to hide.

What changing over involves

What you changed

What gets adjusted

Roughly how long

New label roll, same bottle

Load the roll, thread the web

15–60 minutes

Different label size, same bottle

Label length setting, coder position

15–60 minutes

Different bottle diameter

Conveyor guides, applicator height and pressure

15–60 minutes

Different bottle height

Applicator height, label position setting

15–60 minutes

Diameter changes are adjustments, not parts. You reposition the guides and the applicator. There’s no change-part kit to buy per bottle size, which is what makes this machine work for contract packing.

Keep a settings sheet by the machine. Applicator height, label length and coder position for each SKU. Written down, a repeat changeover takes a fraction of the first one.

Label supply changes matter more than they look. A different backing paper thickness or a different core diameter changes how the web feeds. If you switch label printers, run a test before you run a batch.

Three things to check before you buy any labeling machine

01

Label placement, bottle after bottle

One label applied straight in a demo proves nothing. Ask how consistent placement is across a full roll, as the roll diameter shrinks. We run your bottles with your labels at factory acceptance testing before the machine ships, and you see the results.

02

The manual

Your operator threads the web, sets label length and adjusts the applicator. They need an English manual with the settings procedure in it — not a translated parts list. Ask to see it before you order.

03

Installation and training

The machine runs out of the crate. Getting it labeling cleanly across all your SKUs takes someone who's set one up before. Our engineers install it, dial in each of your bottles, and show your operators how to diagnose a crooked label.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Container and Label Before You Order

Send us your container and a roll of your label. We run them on the machine and send you photos. You decide whether to talk quotes after that.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Deep Dive FAQ

How much does a labeling machine cost?

It depends on your bottle diameter range, your line speed, and whether you need a coder for batch and expiry printing. Send us your bottle and label artwork and we’ll reply within one business day. Most quotes include a layout showing where it fits.

Will it label my bottles?

If they’re round and within the diameter range, almost certainly. Send us a bottle and a label roll and we’ll run a sample before you order — we’d rather show you than describe it.

Why do my labels go on crooked or wrinkled?

Usually one of three things, and often not the machine. Bottles that aren’t traveling straight when they reach the applicator, a label web that’s running slack, or an applicator arrangement set for a different bottle shape. Check those before you adjust anything else.

Does it print batch codes and expiry dates?

A coder can be fitted to print on the label as it’s fed, before it reaches the bottle. Tell us what you need to print and we’ll specify it.

Can it do front and back labels?

Not on this model — the APC-T1 applies one wrap-around label. For separate front and back labels on a round bottle, or for square bottles needing multiple panels, the APC-T2 is the machine.

Does it work on US 60Hz power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

Can I add this to a line I already have?

Yes. It’s the last station, after capping and sealing, and it runs on its own conveyor. Tell us your existing conveyor height and belt width and we’ll match it.

Do your machines meet US electrical certification requirements?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us a bottle and a label roll

We’ll run a sample on our own machine and send you a photo before you commit to anything. If your bottle shape needs a different machine, we’ll tell you which one instead of selling you this.

Send your line layout and we’ll show you where the labeler fits and how much conveyor length you need either side.

Scroll to Top