Shrink Sleeve Applicator and Shrink Tunnel

Tamper-Evident Neck Bands for Supplement Bottles

A foil seal under the cap tells your customer the bottle wasn’t opened — but only after they’ve opened it. A band over the cap tells them before they buy.

50 to 150 Bottles/Min
Bottles Ø25–125 mm
PVC, PET and OPS Film

Two Layers of Tamper Evidence, Not One

Under the cap — an induction seal, foil welded to the bottle mouth. It proves the bottle is intact, but only once the customer has it in their hands and twists the cap off.

Over the cap — a shrink band. It crosses the gap between cap and neck, so it has to be cut or torn before the cap turns. A customer standing in a store can see it, and so can the person checking returns at your distributor.

Most US supplement brands run both. The foil is the seal; the band is what the shelf sees. If your bottling line already has an induction sealer, this is the station that sits right after it.

Two machines do the job. An applicator cuts film from a roll, opens it and drops it over the neck — nothing is glued and nothing presses on the bottle. A tunnel then heats the band so it shrinks tight onto the cap. Without the tunnel the band sits loose.

Why AIPAK Sleeve Applicators

Nothing Sticks to the Bottle

Nothing Sticks to the Bottle

Film comes off a roll as a flat tube, is cut to length and dropped over the neck. Nothing is glued and nothing presses on the container — which is why glass runs the same as PET, with no change but the knife plate.

Applicator and Tunnel from One Supplier

Applicator and Tunnel from One Supplier

Two machines that have to be timed to each other. Buying them separately means two suppliers pointing at each other when the band comes out crooked or half-shrunk.

We Run Your Bottles First

We Run Your Bottles First

Send us 30 bottles of each size and a 200 m roll of each film. We band them, shrink them, and send you the result with the rate we actually held — before you order, not after.

Knife Plates for Your Whole Range

Knife Plates for Your Whole Range

Ø25–50, Ø51–90 and Ø91–125 mm. Tell us every bottle size you run and we’ll quote the plates together, rather than leaving you to find out later that one size needs another plate.

Which Pair Do You Need?

Buy them as a pair. An applicator without a tunnel leaves the band sitting loose on the neck. A tunnel without an applicator has nothing to shrink.

1. How fast is your bottling line?

The APK-SL50 runs 50 bottles a minute on single-phase power — no new electrical supply needed. The APK-SL150 runs up to 150 and needs three-phase.

2. How big is your bottle — including the cap?

The band has to clear the cap, so measure the cap, not the bottle body. And check the tunnel before the applicator: the APK-SH7 takes bottles up to Ø100 mm and 280 mm tall, where the applicator would go to 120. The tunnel is the real ceiling.

3. What film are you running?

PVC, PET and OPS all run. Film thickness differs between the two applicators — 0.03 to 0.13 mm on the APK-SL50, 0.035 to 0.080 mm on the APK-SL150. Tell us your film spec before you choose.

 

 Entry pairLine pair
ApplicatorAPK-SL50APK-SL150
TunnelAPK-SH7APK-SH15
Speed50 bottles/minup to 150 bottles/min
Bottle Ø28–100 mm25–125 mm
Bottle heightup to 280 mmup to 350 mm
Powersingle-phase applicator + tunnelthree-phase

Model comparison

Model

Function

Speed

Bottle Ø

Bottle height

Power

APK-SL50

Applicator

50 bottles/min

28–120 mm

up to 250 mm

220 V single-phase, 3 kW

APK-SL150

Applicator

up to 150 bottles/min

25–125 mm

up to 350 mm

three-phase, wired for your U.S. supply, 3 kW

APK-SH7

Shrink tunnel

0–35 m/min

up to 100 mm

up to 280 mm

7 kW

APK-SH15

Shrink tunnel

0–45 m/min

up to 125 mm

up to 350 mm

15 kW

Size the tunnel first. The applicator takes a wider bottle range than the tunnel does — on the entry pair the ceiling is Ø100 mm, where the applicator alone would reach 120.

And treat every speed on this page as a starting point. Bottle shape, cap profile and film all change the rate. We confirm yours on your own samples.

Where Banding Sits on Your Line

NINE STATIONS, ONE LINE

Bottle Unscramble

Bottle Unscrambler

Bottle Air Cleaner

Bottle Air Cleaner

APC-24 Automatic Electronic Counting Machine-1

Counting Machine

Air-Cooled-Induction-Sealer-2

Induction Sealer

APC-D902 Screw Capper-1

Capping Machine

APC-C120 Desiccant Inserter

Desiccant or Cotton Inserter

APK-SL150 Shrink Sleeve-3

Sleeve Applicator

APK-SH7-Electric-Shrink-Tunnel-3

Shrink Tunnel

APC-T1 Round Bottle Labeling Machine-1

Labeller

The band goes on after the cap, because it has to cross the cap-to-neck gap. The tunnel sits immediately after the applicator with nothing between them — the band isn’t held on by anything until it shrinks, so any extra handling in between will move it.

The body label goes on last. A band that’s already shrunk won’t interfere with it.

One thing worth checking: if your line runs faster than the applicator, the applicator becomes your line speed. A 50-bottle-a-minute applicator on a line built for 100 halves your output.

What These Machines Are Banding

Supplement bottles with a foil seal
Gummy and powder jars
Amber glass for herbals and tinctures
Bottles that ship long distance

Documentation & Selection Support

Verify our specifications and simplify your procurement process with our official documentation.

Shrink-Sleeve-Applicator-and-Shrink-Tunnel-2

Product Portfolio

Full specifications for both applicators and both tunnels — bottle ranges, film specs, knife plate ranges, power and footprint.
Quality Assurance

CE Declaration of Conformity

Issued for the machine you buy, not for a range. Material certificates available on request.
Technical Standards

Send Us Bottles and Film

30 bottles of each size and a 200 m roll of each film. We band them, shrink them and send you the result with the rate we held — free, before you order.

FAQ

What's the difference between a shrink band and a label?

A label is glued to the bottle and carries your artwork. A shrink band is a tube of film dropped over the cap with nothing holding it on until heat shrinks it. Its job is to show whether the cap has been turned.

Do I still need an induction seal?

Most brands run both. The foil seal sits under the cap and proves the product is intact. The band sits over the cap and is what a customer sees before buying.

Which machine limits my bottle size — the applicator or the tunnel?

Usually the tunnel. Our applicators take bottles from Ø25 to 125 mm; the smaller tunnel stops at Ø100 mm and 280 mm tall. Send us your bottle and we’ll check both.

How fast will it run on my bottle?

We won’t know until we run it. Bottle shape, cap profile and film all change the rate. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll tell you the rate we held — not a headline number.

Steam tunnel or electric tunnel?

Electric. We don’t offer a steam tunnel, and we wouldn’t recommend one for supplement bottles. Steam tunnels put moisture into the packing area, and a bottle that leaves the tunnel damp is a bottle your body label may not stick to. They also need a boiler, condensate drainage and regular cleaning of the steam box — three things an electric tunnel doesn’t ask of you.

For neck bands on PVC, PET or OPS film, hot air does the job. Steam earns its place on full-body sleeves with complex bottle shapes, where the film has to pull into a recess — and that’s a different product from what most supplement brands run.

What film can I use?

PVC, PET and OPS. Thickness range differs between the two applicators — 0.03 to 0.13 mm on the APK-SL50, 0.035 to 0.080 mm on the APK-SL150. Rolls with a 5 to 10 inch core, bought locally.

Does it need compressed air?

The APK-SL150 doesn’t — power only. 

Does it run on US power?

Yes. All four machines are built for 60 Hz and wired for your U.S. supply. The APK-SL50 runs on single-phase power; the APK-SL150 and both tunnels need three-phase.

How fast can I get spare parts?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Do your machines meet U.S. electrical certification requirements?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

Send Us Bottles and Film. Then We'll Talk Speed.

The rate any supplier quotes you is a rate on their bottle, not yours. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll run them and tell you the rate we can hold.

If you already have an applicator or a tunnel, say so — you probably need one machine rather than two, and that changes the quote substantially.

  • Reply within one business day
  • Trial run on your own bottles, free
  • We keep your artwork and specs confidential.
Scroll to Top