APK-SH7 Electric Shrink Tunnel

Hot-air shrinking for bottles up to Ø100 mm, 7 kW

A band dropped over the cap sits loose until something shrinks it. This tunnel does that with recirculated hot air — no boiler, no steam, and the bottle leaves dry. Bottles up to Ø100 mm and 280 mm tall, on a belt you set to match the applicator ahead of it.

  • Bottle size — up to Ø100 mm and 280 mm tall

  • Belt speed — 0 to 35 m/min, set on the panel

  • Power — 7 kW, single- or three-phase, 50/60 Hz

  • Footprint — 1,000 × 450 mm, the smaller of our two tunnels

Trial run on your own bottles before you order    |    Installation and training    |    Spare blades in your quote

Is this the right machine for you?

✓ Yes, if…

✕ Buy something else if…

Hot Air, Circulated — Not Blown at the Bottle

A band shrinks from the heat around it, not from air hitting it. The tunnel recirculates hot air through the chamber so the band is warmed on every side at once. A single jet blowing at one face is what leaves a band tight at the front and loose at the back.

Temperature and Belt Speed, Both on the Panel

Two settings control the result: how hot the chamber runs, and how long the bottle spends in it. Between them they give you a window — hot enough and slow enough to pull the band tight, cool enough and fast enough not to distort the bottle or scorch the film. Finding that window on your film is what commissioning is for.

Electric, So the Bottle Leaves Dry

Hot air needs power and nothing else. No boiler, no condensate drain, no steam box to clean out — and no moisture left on the bottle for your labeler to deal with a meter downstream. That last point is the one most buyers only think of after they’ve bought a steam tunnel.

Conveyor Through the Chamber

Bottles run through on their own conveyor, so the tunnel drops into a line rather than needing a transfer at each end. Belt speed is set to match the applicator ahead of it.

Technical specification

Specification

APK-SH7

What it means for you

Heating

Electric, recirculated hot air

No boiler, no condensate drain

Power

7 kW

Half the draw of the APK-SH15

Supply

Single- or three-phase, 50/60 Hz

Built to your U.S. supply. We confirm the voltage with your quote

Max bottle diameter

Ø100 mm

The real ceiling of the entry pair — the applicator alone would reach 120

Max bottle height

280 mm

Measure to the top of the cap

Belt speed

0–35 m/min

Set to match the applicator ahead of it

Film

PET, PVC

Each shrinks at a different temperature

Dimensions

1,000 × 450 × 1,700 mm

Fits at the end of a line without a layout change

Weight

300 kg

—

Model comparison

Model

Function

Speed

Bottle Ø

Bottle height

Power

APK-SL50

Applicator

50 bottles/min  

28–120 mm

up to 250 mm

single-phase, 3 kW

APK-SL150

Applicator

up to 150 bottles/min

25–125 mm

up to 350 mm

three-phase, 3 kW

APK-SH7

Shrink tunnel

0–35 m/min

up to 100 mm

up to 280 mm

7 kW

APK-SH15

Shrink tunnel

0–45 m/min

up to 125 mm

up to 350 mm

15 kW

Buy the tunnel with the applicator, and size the tunnel first. It’s the tunnel that sets your bottle ceiling, not the applicator.

Ideal Applications & Industries

Neck bands on supplement bottles

The most common job. A band 25 to 50 mm long over the cap, shrunk tight enough that it has to be torn before the cap turns.

Gummy and powder jars

Wide-mouth jars where the cap is the widest point. The cap diameter is what has to clear the tunnel, not the jar body.

Amber glass for herbals and tinctures

Glass holds heat longer than PET, so it usually runs at a lower temperature and a slightly slower belt. Same tunnel, different settings.

PVC and PET film

Each shrinks at a different temperature. Switching film means finding the window again — which takes minutes on the panel, not a parts change.

Changeover

A tunnel has no change parts. What it has is a window.

What changed

What you adjust

Roughly

Same bottle, new film roll

Nothing

—

Different bottle height

Conveyor height and air deflectors

15–30 minutes

Different bottle diameter

Nothing — as long as it’s inside the tunnel’s range

—

PVC → PET film

Temperature and belt speed. PET shrinks at a higher temperature

A few minutes

Different band length

Belt speed

A few minutes

The window is a temperature high enough to pull the band tight and low enough not to distort the bottle or scorch the film. It’s narrower on thin film and on glass, and it’s what we set during commissioning — on your bottle and your film, not on a sample of ours.

What to check before you buy

01

The shrink, not the tunnel

Any tunnel will shrink a band. What matters is whether it shrinks evenly — tight at the cap, tight at the neck, no wrinkles at the seam. Ask any supplier to run your bottle and your film and send you the finished bottle, not a photo of the machine.

02

The tunnel's ceiling, not the applicator's

Applicators take a wider bottle range than tunnels do. Check the tunnel's maximum diameter and height against your tallest bottle, measured over the cap.

03

Installation and training

Our engineer comes to your plant. Travel and on-site costs are quoted separately. Installation isn't free anywhere — it's either a line item or it's inside the machine price. We quote it as a line item so you can see it.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Bottles Before You Order

Send us 30 bottles of each size and a 200 m roll of each film. We band them, shrink them and send you the finished bottles, with the rate we held.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Questions About the APK-SH7

Do I need a tunnel at all?

Yes, if you’re applying shrink bands. The applicator drops the band over the neck, but nothing holds it there — it sits loose until heat shrinks it. An applicator without a tunnel produces bottles with bands sliding off them.

Steam tunnel or electric?

We build electric, and we’d recommend it for supplement bottles. Steam puts moisture into your packing area, needs a boiler and a condensate drain, and leaves the bottle damp — which is a problem a meter later when your labeler tries to stick a label to it. Steam earns its place on full-body sleeves with complex bottle shapes, where the film has to pull into a recess. That’s a different product from what most supplement brands run.

What temperature should I run?

It depends on your film, your bottle and your band length, so we set it during commissioning rather than quoting a number here. As a rule PVC shrinks lower than PET, and glass needs a lower setting than plastic because it holds heat.

Will it distort my bottle?

Not if the window is set properly. PET bottles are the ones to watch — too hot and too slow and the shoulder softens. That’s why we run your bottle and your film before you order, and why the result you get back is a finished bottle rather than a photo.

What happens if the line stops with a bottle inside?

The tunnel backs off the heat and lets the chamber cool rather than holding a bottle at shrink temperature. A bottle left in a hot chamber for a few minutes scorches the band, and a PET bottle can soften at the shoulder. The protection means an unplanned stop costs you one bottle rather than a batch.

Can it shrink a full-body sleeve, not just a neck band?

A longer band needs longer in the chamber, so the belt slows down and your rate drops. Whether it works well depends on the bottle shape — a straight-sided bottle is straightforward, a bottle with a waist is not. Send us both and we’ll tell you honestly.

Does it run on US power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

Is 7 kW enough for my line?

It’s matched to the APK-SL50 at 50 bottles a minute. Above that, the band spends less time in the chamber and the tunnel has to run hotter to keep up — which narrows your window. If your line runs faster, the APK-SH15 is the right tunnel.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us bottles and film. Then we'll talk speed.

The rate any supplier quotes you is a rate on their bottle, not yours. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll run them and tell you the rate we can hold — before you order, not after.

  • Reply within one business day
  • Trial run on your own bottles
  • Your artwork and specs stay with us
Scroll to Top