APC-SL50 Shrink Sleeve Applicator — 50 Bottles a Minute

Tamper-evident neck bands on single-phase power

A foil seal under the cap tells your customer the bottle wasn’t opened — but only after they’ve opened it. A band over the cap tells them before they buy. This machine cuts film from a roll, opens it and drops it over the neck. And it runs on single-phase power, so it goes in without a new electrical supply.

  • Speed — up to 50 bottles a minute

  • Bottle diameter — Ø28 to 120 mm, across three knife plate ranges

  • No compressed air — one less utility at this station

  • Power — single-phase, 3 kW

Trial run on your own bottles before you order | Installation and training | Spare blades in your quote

Is this the right machine for you?

✓ Yes, if…

✕ Buy something else if…

Nothing Sticks to the Bottle

The film arrives as a flat tube on a roll. The machine opens it, cuts it to length and drops it over the neck. Nothing is glued and nothing presses on the bottle, which is why the same machine handles glass and PET without changing anything but the knife plate.

Three Knife Plate Ranges

Ø25–50, Ø51–90 and Ø91–125 mm. The plate matches the film diameter to your bottle, so the band drops cleanly instead of catching on the cap. Your bottle range decides how many plates you need — tell us all your sizes and we’ll quote them together.

Servo Film Feed and Servo Knife

Feed and cutting each run on their own servo, so the cut length holds rather than drifting as the roll empties. Cut length is set on the touchscreen from 30 to 250 mm.

No Compressed Air

This machine needs power and nothing else. On a line where the capper and the filler are already drawing air, that’s one less demand on your compressor — and one less thing to plumb at the end of the line.

Technical specification

Specification

APK-SL50

What it means for you

Type

Linear

Feeds in line with your conveyor

Speed

0–50 bottles/min

Your rate depends on your bottle and film — we confirm it on your samples

Bottle diameter

Ø28–120 mm

Across three knife plate ranges

Bottle height

up to 250 mm  

—

Knife plate ranges

Ø25–50 / Ø51–90 / Ø91–125 mm

One plate covers one range. Tell us your full bottle range

Cut length

30–250 mm

30–50 mm covers a neck band; longer cuts reach the shoulder or the body

Sleeve position

Cap seal, shoulder, middle body, full body

Same machine, different cut length and film

Film materials

PVC, PET, OPS

—

Film thickness

0.03–0.130 mm

—

Roll core

5″–10″

Standard rolls, bought locally

Bottle materials

PET, PVC, glass, metal, HDPE, PP, PS

Nothing touches the bottle under pressure, so glass runs like plastic

Compressed air

Not required

One less utility at this station

Power

Single-phase, 3 kW

Built to your U.S. supply. We confirm the voltage with your quote

Construction

SUS304

—

Dimensions

1,500 × 800 × 2,000 mm

Add clearance for roll loading

Weight

600 kg

No special foundation

Controls

PLC and touchscreen

—

Model comparison

Model

Function

Speed

Bottle Ø

Bottle height

Power

APK-SL50

Applicator

50 bottles/min  

28–120 mm

up to 250 mm

single-phase, 3 kW

APK-SL150

Applicator

up to 150 bottles/min

25–125 mm

up to 350 mm

three-phase, 3 kW

APK-SH7

Shrink tunnel

0–35 m/min

up to 100 mm

up to 280 mm

7 kW

APK-SH15

Shrink tunnel

0–45 m/min

up to 125 mm

up to 350 mm

15 kW

Buy the pair. An applicator without a tunnel leaves the band sitting loose on the neck.

And size the tunnel first. The applicator takes a wider bottle range than the tunnel does — on the APK-SH7 the ceiling is Ø100 mm, where the applicator would go to 125.

Ideal Applications & Industries

Supplement bottles with a foil seal

The band goes on after capping and sealing, crossing the gap between cap and neck. Two tamper features on one line, and the band is the one your customer sees on the shelf.

Gummy and powder jars

Wide-mouth jars where the cap is the widest point on the container. Check the cap diameter, not the bottle diameter — that’s what the band has to clear.

Amber glass for herbals and tinctures

Glass runs on the same machine as plastic. Nothing presses on the container and nothing is glued to it.

Bottles that ship long distance

A band that arrives torn tells your distributor the bottle was handled. That’s the point of it — and it’s why the shrink has to be tight, not just present.

Changeover

Film size changes on the screen. Bottle diameter changes the knife plate.

What changed

What you adjust

Roughly

Same bottle, new film roll

Load the roll, set the cut length

A few minutes

Band length changes

Cut length on the touchscreen

A few minutes

Bottle diameter moves within one knife plate range

Guides and centering post, on handwheels

15–30 minutes

Bottle diameter crosses into another range

Change the knife plate

15–30 minutes

Knife plates cover Ø25–50, Ø51–90 and Ø91–125 mm. One plate ships with the machine; tell us your full bottle range and we’ll quote the rest.

The tunnel needs no change parts for a different bottle — only its temperature and belt speed, both set on the panel.

What to check before you buy

01

The speed on your bottle, not on theirs

Every supplier's headline rate was measured on some bottle. Yours has a different shoulder, a different cap and a different film. Ask any supplier to run your samples and quote the rate they held — we ask for 30 bottles of each size and a 200 m roll of each film before we confirm anything.

02

The tunnel, not the applicator

The applicator takes a wider range of bottles than the tunnel does. Check the tunnel's maximum diameter and height against your tallest bottle first — it rules out more machines than speed does.

03

Installation and training

Our engineer comes to your plant. Travel and on-site costs are quoted separately. Installation isn't free anywhere — it's either a line item or it's inside the machine price. We quote it as a line item so you can see it.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Bottles Before You Order

Send us 30 bottles of each size and a 200 m roll of each film. We band them, shrink them and send you the finished bottles, with the rate we held.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Questions About the APK-SL50

What's the difference between a shrink band and a label?

A label is glued to the bottle and carries your artwork. A band is a tube of film dropped over the cap with nothing holding it on until heat shrinks it. Its job is to show whether the cap has been turned.

Do I still need an induction seal?

Most brands run both. The foil seal sits under the cap and proves the product is intact. The band sits over the cap and is what a customer sees before buying.

How fast will it run on my bottle?

We won’t know until we run it. Bottle shape, cap profile and film all change the rate. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll tell you the rate we held — not a headline number.

Does it need compressed air?

No. Power only.

How many knife plates do I need?

One for each diameter range your bottles fall into: Ø25–50, Ø51–90, Ø91–125 mm. If all your bottles sit in one range, one plate covers them. Tell us every size you run and we’ll quote it properly rather than leaving you to discover it later.

Can it do full-body sleeves, not just neck bands?

The machine cuts from 30 to 250 mm, so yes. But a full-body sleeve is a different job: the film is thicker, the artwork has to register, and the tunnel matters much more. Tell us which you’re planning before we quote.

What film and roll size does it take?

PVC, PET or OPS, 0.03 to 0.13 mm thick, on rolls with a 5 to 10 inch core. Standard stock you buy locally.

Does it run on US power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us bottles and film. Then we'll talk speed.

The rate any supplier quotes you is a rate on their bottle, not yours. Send us 30 bottles of each size and a 200 m roll of each film, and we’ll run them and tell you the rate we can hold — before you order, not after.

  • Reply within one business day
  • Trial run on your own bottles
  • Your artwork and specs stay with us
Scroll to Top