APC-M1 Air-Cooled Induction Sealer

This induction sealer bonds a foil liner to the bottle land as bottles pass under the coil, at 50 to 120 bottles per minute. If you’re already capping and your bottles still go out without a tamper seal, this is the machine that closes that gap. It handles 15 to 50 mm bottle openings.

  • 50 to 120 bottles per minute— matches a counting line running up to 120 bpm
  • 15 to 50 mm bottle openings, round, oval, square or flat-square

  • Air-cooled— no water supply to plumb, no chiller to maintain

Direct from our factory|Lead time confirmed in your quote|Installation and training available|Spare parts listed in your quote

Is this the right sealer for your line?

✓ This is a fit if…

✕ Look elsewhere if…

Technical specification

Parameter

Value

What this means for you

Sealing speed

50 – 120 bottles / min

Match this to your capper, not your counter

Bottle opening diameter

15 – 50 mm

Your bottle neck has to fall inside this

Bottle shapes

Round, oval, square, flat-square

One machine covers all four

Cooling

Multi-channel air cooling

No water supply or chiller needed

Power adjustment

Automatic, by foil size

You set the product, the machine sets the power

Overload protection

Stops and alerts on under- or over-power

You find out at the machine, not at QC

Power

3.0 kW, 60 Hz

Built to your U.S. supply. We confirm the voltage with your quote

Machine dimensions

1350 × 900 × 1300 mm

Add clearance at the front for head height adjustment

Machine weight

220 kg

—

Conveyor speed

Up to 10 m/min

Adjustable to match the line ahead

Foil liner thickness

0.2 – 1.2 mm

Send us your liner spec

 

Model comparison

Model

Speed

Bottle opening

Cooling

Best for…

 

APC-M1

50–120 btl/min

15–50 mm

Air

Brands running one shift, up to 120 bpm, standard supplement bottles

You are here

APC-M2

Up to 200 btl/min

15–150 mm

Water

Two or three-shift operations, wide-mouth jars, high-speed lines

View →

Both machines seal the same way. What changes is how long the coil can run flat out, and how wide a bottle opening it covers.

How the seal is made

The coil generates a magnetic field that heats the foil layer inside your cap liner. The polymer coating on the foil melts and bonds to the bottle land. The cap stays cool, and so does the product underneath — nothing in the bottle gets heated.

Automatic power adjustment

Sealing power adjusts to the foil size automatically. You don’t calculate a wattage for each SKU — set the product, and the machine matches the coil output to what it sees.

If power runs too low or overloads, the machine stops and tells you. You find out at the machine rather than three pallets later at QC.

Multi-channel air cooling

Multiple air channels carry heat away from the induction components. That keeps coil output stable through a shift and extends the life of the electronics.

Air cooling means no water line to plumb and no chiller to maintain. For single-shift running it’s the simpler choice. If you’re running continuously, look at the water-cooled model instead.

Ideal Applications & Industries

Tablet and capsule bottles

Standard 60, 90 and 120-count bottles with a pre-inserted foil liner. The most common setup on this machine.

Gummy bottles

Gummy bottles usually have a wider opening — check yours against the 15 to 50 mm range. Gummies also hold moisture, so the seal is doing real work here, not just providing tamper evidence.

Powder containers

Powder sitting on the bottle land stops the seal bonding. If you’re filling powder, the land has to be clean when the cap goes on. That’s a filling problem, but it shows up here.

What changing over involves

What you changed

What gets adjusted

Roughly how long

Same bottle, different cap color

Nothing

0

Different bottle height

Head height

15–30 minutes

Different cap diameter

Head height, possibly the guide rails

15–30 minutes

Different liner material or thickness

Power setting, then a seal test

15–30 minutes

Fewer format parts than most machines on your line. A capper has chucks, a labeler has change parts. This has head height and power. That’s most of it.

Liner changes need a test run. A thicker foil or a different polymer coating seals at a different power setting. Seal a few and check them before you run a batch.

Write down what worked. Keep the power setting and head height for each SKU on a sheet by the machine. It saves re-finding them every changeover.

Three things to check before you buy any induction sealer

01

The seal has to hold, batch after batch

A seal that looks right isn't the same as a seal that passes a peel test. Ask any supplier how they verify it, and ask to see the settings for a liner like yours. We seal your bottles with your caps and liners at factory acceptance testing before the machine ships.

02

The manual

Your operator sets head height and power. They need to know what to do when a seal fails — and it will fail sometimes, usually because of the cap or the bottle, not the machine. Ask to see the English manual before you order.

03

Installation and training

Getting the sealer running takes ten minutes. Getting it to seal reliably across all your SKUs takes someone who's done it before. Our engineers install it, dial it in on your products, and show your operators how to read a failed seal.

Why buy from us

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Bottle, Cap and Liner Before You Order

Send us a bottle, a cap and a liner. We seal them on the machine and send you photos. You decide whether to talk quotes after that.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

FAQ

How much does an induction sealer cost?

It depends on your line speed and bottle opening size, and whether air or water cooling fits your shift pattern. Send us your bottle, cap and target rate and we’ll reply within one business day. Most quotes include a layout showing where it fits.

Will it seal my caps and liners?

Probably, if your liner has a foil layer. Liners without foil won’t seal by induction at all. Send us a bottle, a cap and a liner — we’ll seal one and send you a photo before you order.

Why do some of my seals fail?

Most failed seals aren’t the sealer. The usual causes are a liner that isn’t seated flat, flashing or molding marks on the bottle land, product dust on the land, or cap torque that’s too low. Check those before you adjust the machine.

Do I need air cooling or water cooling?

Air cooling suits single-shift running up to 120 bottles per minute, with bottle openings from 15 to 50 mm. It needs no water supply. Water cooling runs up to 200 bottles per minute, covers openings up to 150 mm, and holds output through continuous shifts.

Does it work on US 60Hz power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

Can I add this to a line I already have?

Yes. It goes between your capper and your labeler on its own conveyor. Tell us your existing conveyor height and belt width and we’ll match it.

Do your machines meet US electrical certification requirements?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

How much floor space do I need?

The machine is 1350 × 900 × 1300 mm. Add clearance at the front for head height adjustment.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us a bottle, a cap and a liner

We’ll seal one on our own machine and send you a photo before you commit to anything. If your liner won’t seal by induction, we’ll tell you that instead of selling you a machine that can’t do the job.

Send your line layout and we’ll show you where the sealer fits and how much conveyor length you need.

Scroll to Top