Home » APC-D903 High Speed Screw Capper
APC-D903 High Speed Screw Capper
The APC-D903 is our high-speed screw capper, built for lines running past the point where a standard capper becomes the bottleneck. It’s the capping station in our high-speed bottling line, alongside a 32-channel counter and a water-cooled induction sealer.
- Built for high-speed lines— the capping station in our 70 to 160 bottle-per-minute line
- Screw closures— standard, tamper-band, double-layer and flip-top plastic caps
- Pairs with water-cooled sealing— at this rate, an air-cooled sealer can’t hold output
Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote
Is the APC-D903 the right capper for you?
✓ This is a fit if…
- You're capping plastic screw caps — standard, tamper-band, double-layer or flip-top
- Your line runs faster than 120 bottles per minute
- Your counter is 32 or 48 channels
- You need adjustable torque — tight enough to hold a foil seal, loose enough to open
- You want bad caps caught here, not discovered at the sealer or by your customer
✕ Look elsewhere if…
- Your caps press on rather than screw on → the APC-D904 is the press-on machine. Pressing a screw cap or screwing a press cap both damage the cap
- You have oddly shaped bottles that are hard to hold → the APC-D901 combines pressing and screwing, and was built for the positioning problems that come with non-round bottles
- Your line runs 120 bottles per minute or less → the APC-D902 does the same job for less
- You're using metal caps or roll-on closures → different mechanism entirely. Tell us your closure and we'll say what it takes
- You're capping glass → talk to us first about the handling arrangement
Technical specification
Parameter | Value | What this means for you |
Capping speed | 60 – 180 bottles / min | Match this to your counter, and check your sealer keeps up |
Cap types | Standard, tamper-band, double-layer, flip-top plastic caps | Screw caps only — press-on caps need the D904 |
Capping method | Three pairs of friction wheels | No chuck to swap between cap diameters |
Torque | Adjustable (Customizable via friction wheels / PLC control) | The single most important setting on this machine |
Bottle size range | Φ30 – Φ100 mm | Your bottle has to fall inside this |
Cap diameter range | Φ20 – Φ50 mm |
|
Detection | No bottle / no cap / crooked cap / reversed cap / missing foil liner | Bad bottles are rejected here, not at the sealer |
Power | 60 Hz, built to your U.S. supply | We confirm the voltage and power with your quote |
Compressed air | 0.6 MPa, 0.3 m³/h | Small demand — most existing compressors cover it |
Machine dimensions | 2550 × 1050 × 1900 mm | Check your line length — this is a long station |
Machine weight | 680 kg |
At 2550 mm this is a long station. Allow conveyor run-in so bottles are travelling straight and evenly spaced before they reach the cap chute.
Model comparison
Model | Speed | Method | Best for… |
|
APC-D901 | 30–80 btl/min | Press and screw | Shaped, flat or oval containers that are hard to hold | |
APC-D902 | 50–120 btl/min | Screw, friction wheels | Standard round bottles at line speed | |
APC-D903 | 60–180 btl/min | Screw, high speed | High-speed lines above 120 bottles per minute | You are here |
APC-D904 | 40–120 btl/min | Press only | Caps that push on rather than screw on |
The choice is decided by your closure, not by your line speed. A press-on cap on a screw capper and a screw cap on a press capper both come out damaged.
Friction wheel capping, adjustable torque
Three pairs of friction wheels grip the cap and turn it down onto the thread. Tightness adjusts without changing parts, and because the wheels grip rather than clamp, the cap surface isn’t marked.
Torque matters more here than most buyers expect. Too loose and the foil liner won’t press against the bottle land, so the induction seal fails downstream. Too tight and your customer struggles to open the bottle. It’s one setting, and it decides two problems.
Stepped cap elevator
Caps are lifted by a stepped elevator rather than a vibratory bowl. It runs quieter, and cap delivery stays steady rather than surging.
Caps that arrive facing the wrong way drop back into the hopper instead of being fed to the bottle. That’s what keeps a wrong-way cap from becoming a jam.
What gets rejected here
The machine stops if there’s no bottle or no cap. It rejects a bottle if the cap went on crooked, if the cap went on upside down, or if the bottle has no foil liner in the cap.
That last one is worth reading twice. A bottle with no liner will pass through your induction sealer without sealing, look fine, and reach your customer unsealed. Catching it here — before the seal step — is the difference between a rejected bottle and a complaint.
Ideal Applications & Industries
Supplement bottles with tamper-band caps
The tamper band has to break cleanly when the customer opens it, which depends on how far the cap is turned down. Torque set once, checked at the start of a run, holds for the shift.
Bottles going through induction sealing
The cap holds the foil liner against the bottle land while the coil heats it. Under-torqued caps and liners with no foil are two of the most common causes of failed seals. This machine catches both.
Contract packers running mixed caps
Standard caps one week, flip-tops the next. The friction wheels handle both without a chuck change — you adjust, you don’t swap parts.
What changing over involves
What you changed | What gets adjusted | Roughly how long |
Same bottle, different cap color | Nothing | 0 |
Different cap diameter | Friction wheel spacing, cap chute | 15–30 minutes |
Different bottle height | Capping head height, conveyor guides | 15–30 minutes |
Different cap type (standard to flip-top) | Cap elevator setup, torque setting | 15–30 minutes |
No chuck kit to buy per cap size. Friction wheels adjust across a range rather than being replaced. If you run several cap diameters, that’s the difference between a settings change and a parts order.
Re-check torque after every changeover. It’s the one setting that isn’t obvious from looking at the bottle. Cap a few, check them, then run.
Write the torque setting down for each SKU. Together with cap type and bottle height, that’s your changeover sheet. A repeat job takes a fraction of the first setup.
Three things to check before you buy any capping machine
Torque, and whether it holds
Ask any supplier what torque range their machine covers and how it's verified. Then ask what happens to that setting over a full shift. We run your bottles with your caps at factory acceptance testing and give you the torque readings, not just a demo.
The manual
Your operator sets torque, wheel spacing and head height. They need to know what an under-torqued cap looks like before it reaches the sealer. Ask to see the English manual with the settings procedure in it.
Installation and training
The machine runs out of the crate. Getting torque right across all your cap types takes someone who's done it before. Our engineers install it, dial in each of your caps, and show your operators how to spot a bad cap.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Bottle and Cap Before You Order
Send us your bottles and caps. We cap them on the machine and send you the video and the readings. You decide whether to talk quotes after that.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Deep Dive FAQ
It depends on your bottle and cap sizes, your line speed, and whether you need the press-on or screw-on configuration. Send us a bottle and a cap and we’ll reply within one business day. Most quotes include a layout showing where it fits.
Torque is adjustable across the range through the friction wheel setting. We set it for each of your cap types during installation, and your operator can adjust it from there.
Usually the bottle isn’t held squarely when the cap comes down, or the cap chute is set for a different diameter. Both are adjustments. This machine also rejects crooked caps rather than passing them on, so you find out at the machine.
The closure decides. A screw cap is turned down onto a thread; a press-on cap is pushed on. Using the wrong machine damages the cap either way. Send us your cap and we’ll tell you which you need.
Yes. It rejects them before they reach the sealer. Without that check, an unlined bottle passes through induction sealing, comes out looking normal, and reaches your customer with no seal.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
Yes. It goes after your counting and desiccant stations, and before the induction sealer. Tell us your existing conveyor height and belt width and we’ll match it.
Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send us a bottle and a cap
We’ll cap it on our own machine and send you the torque readings. If your closure needs the press-on machine instead, we’ll tell you that rather than selling you this one.
Send your line layout and we’ll show you where the capper fits and how much conveyor length you need either side.