APC-D901 Press-Screw Capper

The APC-D901 presses and screws in one station, at 30 to 80 bottles per minute. It was built for the containers that give ordinary cappers trouble — shaped bottles, flat bottles, anything that won’t sit still under a capping head. If your bottle isn’t a plain cylinder, start here.

  • Press and screw in one station— handles closures that need both actions
  • Built for shaped containers— the positioning arrangement is the point of this machine
  • 30 to 80 bottles per minute— steady rather than fast, because odd shapes take longer to hold

Direct from our factory | Lead time confirmed in your quote | Installation and training available | Spare parts listed in your quote

Is the APC-D901 the right capper for you?

✓ This is a fit if…

✕ Look elsewhere if…

Technical specification

ParameterValueWhat this means for you
Capping speed30 – 80 bottles / minSlower than a round-bottle capper, because shaped bottles need holding
Capping methodPress and screw combinedThe cap seats down, then turns
Cap typesStandard, tamper-band, double-layer, flip-top plastic caps 
Container shapesRound and shaped containersThe positioning arrangement is built for the awkward ones
Bottle size rangeΦ20 – Φ120 mm / Height: 50 – 300 mmSend us your bottle — shape matters more than size here
Cap diameter rangeΦ15 – Φ65 mm 
TorqueAdjustable, 0.5 – 4.0 N·mSet tight enough to hold a foil liner, loose enough to open
DetectionNo bottle / no cap, with self-diagnosisStops on a missing bottle or cap. Does not reject a badly applied cap
Power1.5 kW, 60 HzBuilt to your U.S. supply. We confirm the voltage with your quote
Compressed air0.6 MPa, 0.3 m³/hSmall demand — most existing compressors cover it
Machine dimensions2150 × 1050 × 1900 mm 
Machine weight600 kg 

Model comparison

Model

Speed

Method

Best for…

 

APC-D901

30–80 btl/min

Press and screw

Shaped, flat or oval containers that are hard to hold

You are here

APC-D902

50–120 btl/min

Screw, friction wheels

Standard round bottles at line speed

View →

APC-D903

60–180 btl/min

Screw, high speed

High-speed lines above 120 bottles per minute

View →

APC-D904

40–120 btl/min

Press only

Caps that push on rather than screw on

View →

Your closure and your bottle shape decide this, not your line speed. A press-on cap on a screw capper and a screw cap on a press capper both come out damaged.

Press and screw in one action

The head seats the cap down before turning it. For closures that need both — a cap that has to be pushed onto the neck before the thread engages — doing it in one station avoids the alignment loss that comes from splitting the job across two.

Torque is adjustable. Set it tight enough that the foil liner presses against the bottle land, loose enough that your customer can open the bottle. That single setting decides both problems.

Positioning for shaped containers

A round bottle finds its own center under a capping head. A flat or oval bottle doesn’t — it can rotate, tilt, or sit off-center, and a cap applied to a bottle in the wrong position goes on crooked.

The positioning arrangement on this machine holds the container in a fixed orientation through the capping stroke. That’s the whole reason to buy this model rather than a faster one.

Tell us your bottle shape at the quotation stage. The holding arrangement is configured to it before the machine ships.

Stepped cap elevator

Caps are lifted by a stepped elevator rather than a vibratory bowl. It runs quieter and cap delivery stays steady rather than surging.

Caps that arrive facing the wrong way drop back into the hopper instead of being fed to the bottle. That’s what stops a wrong-way cap becoming a jam.

Ideal Applications & Industries

Flat and oval supplement bottles

Flat bottles look good on a shelf and are difficult to cap. They rotate under the head unless something holds them. If you’ve been capping these by hand because the machine kept applying caps crooked, this is the reason why.

Closures that seat before they turn

Some tamper-band and double-layer caps have to be pushed down onto the neck before the thread catches. Screwing without pressing first cross-threads them.

Oval tincture and dropper bottles

A 30 ml oval bottle rotates under a capping head unless something holds it. Dropper caps make it worse — the pipette adds weight off-centre. This is the container that sends people back to hand-capping.

What changing over involves

What you changed

What gets adjusted

Roughly how long

Same bottle, different cap color

Nothing

0

Different cap diameter

Cap chute and capping head

15–30 minutes

Different bottle height

Head height, conveyor guides

15–30 minutes

Different bottle shape

Positioning arrangement, guides, torque check

15–30 minutes

Shape changes take longest. Height and diameter are adjustments. Changing from a round bottle to a flat one means resetting how the container is held, which is the slowest changeover on this machine.

Re-check torque after every changeover. It’s the one setting you can’t judge by looking at the bottle. Cap a few, check them, then run.

Write down the holding setup for each container. Together with torque and head height, that’s your changeover sheet. A repeat job takes a fraction of the first setup.

Three things to check before you buy any capper

01

Torque, and whether it holds

Ask any supplier what torque range their machine covers and how it's verified. Then ask what happens to that setting over a full shift. We run your bottles with your caps at factory acceptance testing and give you the torque readings, not just a demo.

02

The manual

Your operator sets torque, head height and the container holding arrangement. They need to know what an under-torqued cap looks like before it reaches the sealer. Ask to see the English manual with the settings procedure in it.

03

Installation and training

The machine runs out of the crate. Getting a shaped bottle to hold squarely takes someone who's done it before. Our engineers install it, set it up for each of your containers, and train your operators.

Why Choose AIPAK?

One Point of Contact

One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.

We Run Your Bottle and Cap Before You Order

Send us your bottles and caps. We cap them on the machine and send you the video and the readings. You decide whether to talk quotes after that.

A U.S. Number, Answered by Us

+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.

Spare Parts and Lead Time, in Writing

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Deep Dive FAQ

How much does a press-screw capper cost?

It depends on your container shapes, cap sizes and line speed. Send us a bottle and a cap and we’ll reply within one business day. Most quotes include a layout showing where it fits.

Why do I need a press-screw machine instead of a plain screw capper?

Two reasons. Your closure may need seating before the thread engages, or your bottle may be shaped in a way that a standard capper can’t hold squarely. If neither applies, the APC-D902 is faster and costs less.

What torque does it apply, and can I set it?

Torque is adjustable. We set it for each of your cap types during installation, and your operator can adjust from there.

Will it cap my flat bottles?

Probably — that’s what the positioning arrangement is for. Send us a bottle and we’ll run it before you order. Shape is harder to judge from a drawing than from the container itself.

Why do my caps go on crooked?

On a shaped bottle, almost always because the container isn’t held squarely under the head. This machine’s holding arrangement addresses that, but it has to be configured to your specific bottle.

Does it detect crooked caps or missing foil liners?

No. This machine stops for a missing bottle or a missing cap. Crooked-cap, reversed-cap and missing-liner rejection is on the APC-D902. If that check matters to you, tell us at the quotation stage.

Does it work on US 60Hz power?

Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.

Do your machines meet US electrical certification requirements?

Yes. Our machines are certified and use certified electrical components. Because the exact scope depends on the model and electrical configuration you select, our factory confirms it in writing before production.

How do spare parts work?

A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.

Customers Also Interested In...

Send us your bottle and cap

We’ll run it on our own machine and send you a photo plus the torque readings. If your container is straightforward enough for a standard screw capper, we’ll tell you — it costs you less.

Send your line layout and we’ll show you where the capper fits and how much conveyor length you need either side.

Scroll to Top