Gummy Cooling Tunnel
A long air-handling unit with built-in defrost, holding 5 to 10 °C behind your depositor
Gummies that leave the tunnel soft or sweating stick in the mold and tear at demolding. This is the cooling tunnel from our gummy lines, sold on its own: a long air-handling unit that cools the gummies gradually, defrost heaters that keep the humidity down, and a drive motor at the exit that keeps the mold chain level under your depositor.
1. Temperature: 5 to 10 °C inside the tunnel
2. Air handling: a long AHU, with defrost heating elements in the coils
3. Belt: blue PU, suspended off the tunnel floor, tensioned by an air cylinder
4. Washdown: fully welded frame, IP65 electrics, Siemens PLC
Is this the right machine for you?
✓ Yes, if…
- You're adding a depositor, or replacing a tunnel that can't hold temperature
- Your gummies come out soft or sweating, or stick at demolding
- You run gelatin or pectin and need 5 to 10 °C in the tunnel
✕ Buy something else if…
- You're starting from nothing → a complete gummy line is simpler to specify than separate machines
- Your forming area can't hold 25–30 °C and 45% humidity or below → fix the room first. No tunnel makes up for a room that swings
- You need pectin gummies dried → that's a drying room, 20 to 24 hours at 25–30 °C and 25–45% humidity, not the tunnel
A Long AHU, Not a Short Chiller
The air-handling unit runs a long stretch of the tunnel instead of sitting in one short block. Cold air reaches the gummies gradually, so they set from the outside in at an even rate rather than skinning over while the center is still liquid.
Defrost Heaters in the Coils
Hot syrup gives off moisture, and that moisture freezes on the cooling coils. Iced coils move less air and the tunnel gets damp — that’s when gummies start to sweat. Heating elements in the AHU clear the frost, so the humidity in the tunnel stays lower.
Motor at the Tunnel Exit, Not at the Depositor
The drive motor sits at the tunnel exit and pushes the mold chain rather than pulling it from the front. Front-mounted motors pull the chain unevenly, so over time it stops running level — and the depositing station loses accuracy because the molds no longer sit where the nozzles expect them.
Belt Suspended, Not Flush
The blue PU belt runs suspended off the tunnel floor, with an air cylinder holding tension automatically. Belts that sit flush against the tunnel trap spilled syrup underneath; they glue down and they’re hard to clean. Mechanical tensioners wear the belt out faster.
Built to Be Washed
The frame is fully welded and sandblasted, and the electrics are rated IP65, so the tunnel can be washed down with water. Door handles are stainless steel.
Technical specification
| Specification | Gummy Cooling Tunnel |
|---|---|
| Tunnel Length | 8 m / 15 m, sized to your output |
| Refrigerant | R134a / R410A |
| Air Handling | Long AHU, upper and lower zone control, air volume adjustable per layer |
| Defrost | Heating elements in the AHU coils, keeps tunnel humidity lower |
| Belt | Blue non-stick PU, suspended, air-cylinder tensioning |
| Drive | Motor at the tunnel exit, keeps the mold chain level |
| Frame | Fully welded, waterproof sandblasted finish |
| Electrical Protection | IP65, stainless steel control cabinet |
| Door Handles | Stainless steel |
| Control | Siemens PLC, UL or CE certified components |
| Tunnel Temperature | 5–10 °C |
| Power | Built to your U.S. supply at 60 Hz. We confirm the voltage with your quote |
Production Applications
Gelatin gummies
Gelatin sets faster, so the tunnel does most of the work. A steady 5 to 10 °C is what gives you a clean release at demolding.
Pectin and vegan gummies
Pectin sets differently and still needs 20 to 24 hours in a drying room afterward. The tunnel’s job is to get it firm enough to leave the mold cleanly.
Adding to an existing depositor
If your depositor is fine but the gummies come out soft or sticky, the tunnel is usually where the problem is. Tell us what you run now.
What to check before you buy
Humidity, not just temperature
Ask how the tunnel deals with frost on the coils. Once the coils ice up, airflow drops and humidity climbs, and that's when gummies start to sweat.
Where the drive motor sits
Ask whether the motor pulls the mold chain from the depositor end or pushes it from the tunnel exit. It decides whether the chain still runs level after a year.
Installation and training
Ask what's included and what costs extra.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
Free Formulas, Whether You Buy or Not
Gelatin and pectin production formulas, with ingredient ratios and process steps. Yours whether you buy from us or not.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Questions About the Gummy Cooling Tunnel
A short chiller hits the hot molds with very cold air at the entrance. The outside of the gummy sets while the inside is still liquid, and you get cracking and gummies that don’t release cleanly. A long AHU spreads the cooling over the length of the tunnel, so the gummy sets evenly.
Hot syrup gives off moisture that freezes on the cooling coils. Iced coils move less air and the tunnel gets damp, and damp gummies sweat and stick. The defrost heaters clear the coils while the tunnel runs, so the humidity stays lower.
A motor at the depositor end pulls the heavy mold chain unevenly, and over time the chain stops running level. Pushing from the exit keeps it level under the depositor, so the molds stay where the nozzles expect them.
Yes. The frame is fully welded and sandblasted, and the electrics are rated IP65, so the tunnel can be washed down with water between products.
Tell us which depositor you run, its output and your mold size. The tunnel has to match the mold chain and the depositing speed, so we check that before we quote.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Machines that usually sit next to this one:
Send Us Your Output and Your Room Size
Tell us your output, which depositor you run, and how much length you have for the tunnel. We’ll tell you what length it needs and whether it fits.
We reply within one business day.