NF-60A Automatic Tube Filling Machine
Up to 60 tubes a minute, with tubes fed automatically from a magazine
The step from hand-loading tubes to a machine that feeds itself. Empty tubes drop from a sloping magazine into their holders, the print is turned to face forward, and each tube is filled, sealed, coded and trimmed — up to 60 a minute with one operator keeping the magazine full. For plastic and laminated tubes; the NF-60A-M is the aluminum version.
1. Output: up to 60 tubes a minute
2. Automatic tube feeding: tubes drop from a sloping magazine, no hand-loading
3. Tubes: plastic and laminated, Ø13–50 mm, 50–210 mm long
4. Fill: 5 to 250 ml, within ±1%
Is the NF-60A the right size for you?
✓ Yes, if…
- Hand-loading tubes is what's limiting your output
- You need up to 60 tubes a minute
- Your tubes are plastic or laminated
- You'd like the smallest automatic machine in the range — 350 kg
✕ Buy something else if…
- You need under 30 a minute → the semi-automatic NF-30 costs less and runs on single-phase power
- Your tubes are aluminum → the NF-60A-M is a separate machine built for folding aluminum tubes
- You need more than 60 a minute → the NF-80 runs 50–75, the NF-120 up to 120
Tubes Fed from a Sloping Magazine
Empty tubes are loaded into an inclined magazine and drop into their holders one at a time, at a speed you can adjust. One operator keeps the magazine full rather than placing every tube.
Print Turned to the Front Before Filling
A color-mark sensor finds the printed eye-mark on each tube and turns it to face the right way, so every sealed tail lines up with the front of the tube.
Hot Air on the Inside of the Tube
Plastic and laminated tubes are sealed with hot air blown onto the inside of the tail, then pressed flat. The printed outside isn’t scorched.
Seal, Code and Trim
The lot number is stamped into the seal and the tail is trimmed square before the tube is discharged.
Technical specification
| Parameter | NF-60A (plastic, laminated) | NF-60A-M (aluminum) |
| Output | up to 60 tubes/min | up to 60 tubes/min |
| Fill | 5–250 ml | 5–250 ml |
| Accuracy | ±1% | ±1% |
| Tube diameter | Ø13–50 mm | Ø13–35 mm |
| Tube length | 50–210 mm | 50–180 mm |
| Sealing | Hot air, pressed flat | Mechanical folding |
| Tube feeding | Sloping magazine, automatic | Sloping magazine, automatic |
| Power / air | Three phase, 60 Hz. Built to your U.S. supply; we confirm the voltage with your quote | Same |
| Dimensions | 1,800 × 800 × 1,980 mm | 1,800 × 850 × 1,380 mm |
| Weight | 350 kg | 350 kg |
| Options | Water chiller; heated, stirred hopper; feed pump; finished-tube conveyor | Heated, stirred hopper; feed pump; finished-tube conveyor |
Model comparison
Model | Operation | Tubes | Speed | Fill | Power |
NF-30 / NF-30M | Semi-automatic | Plastic / aluminum | 10–30/min | 5–250 ml | Single phase |
NF-60A | Automatic | Plastic, laminated | up to 60/min | 5–250 ml | Three phase |
NF-80 | Automatic | Plastic, laminated | 50–75/min | 5–250 ml | Three phase |
NF-100 | Automatic | Plastic and aluminum | 80–100/min | 5–180 ml | Three phase |
NF-120 | Automatic, twin station | Plastic and aluminum | 80–120/min | 5–250 ml | Three phase |
Industry Applications
Typical OTC products in U.S. supplement and OTC plants:
Antifungal Creams
Athlete’s foot and other OTC antifungal creams in printed laminated tubes, where the print has to line up with the seal on every tube.
Topical Pain-Relief Gels
Menthol and analgesic gels for muscle and joint pain, filled at up to 60 tubes a minute once hand-loading is the limit.
First-Aid Burn Gels
Clear gels in small plastic tubes for first-aid kits and retail.
Antibiotic Ointments in Aluminum Tubes
Ointments that need a full barrier against air and light, folded rather than heat-sealed on the NF-60A-M.
What changing over involves
What changed | What you adjust | Roughly |
Different fill | Pump setting | 15–30 minutes |
Different tube diameter | Tube holders | 15–30 minutes |
Different product | Clean the hopper and pump | 15–30 minutes |
What to check before you buy
Your tube, not a sample tube
Plastic, laminated and aluminum tubes seal in different ways. Ask any supplier to run your tube, not one of theirs.
Plastic or aluminum — or both?
Many semi-automatic fillers seal only one kind of tube. If you run both, ask whether that's one machine or two.
Your power supply
This machine needs three-phase power. Only the semi-automatic NF-30 runs on single phase — check before you choose.
Why Choose AIPAK?
One Point of Contact
One project engineer handles your machine from proposal to commissioning, so you’re not chasing five suppliers for one answer.
We Run Your Tubes Before You Order
Send us a few of your empty tubes and a sample of your product. We need your tube to size the holders and set the sealer anyway, so we fill and seal them on the machine and send them back. You’ll see the seal, the code and whether the print still looks right after the heat — on your own tube and your own product, not a sample we chose.
A U.S. Number, Answered by Us
+1 (213) 526-8644, answered by our engineers 9 AM–7 PM China time, Monday to Friday. That’s evening and overnight in the U.S., so leave a message or send a WhatsApp anytime and we’ll pick it up first thing.
Spare Parts and Lead Time, in Writing
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
NF-60A Automatic Tube Filling Machine Comprehensive Technical FAQ
Because loading tubes by hand is the slow part. On the NF-60A, tubes drop from a sloping magazine into their holders, the print is turned to the front, and the machine fills, seals, codes and trims them. One operator keeps the magazine full, at up to 60 tubes a minute.
A photoelectric sensor checks each holder before the filling station. If a tube misfed from the magazine or didn’t seat, the filler doesn’t fire for that cycle, so no product lands on the machine.
Thick creams and ointments tend to leave a thread of product behind when the nozzle lifts away, and that thread lands where the seal will be. A cut-off nozzle blows off and cuts off the product at the end of each dose, so the break is clean and the seal area stays clear.
A plastic tube is sealed by heating the inside of its tail until the layers soften and fuse. A water chiller, available as an option, keeps the tube holders cool while that happens, so the heat stays at the seal instead of spreading toward the product.
No. The NF-60A fills plastic and laminated tubes and seals them with hot air. Aluminum tubes are folded rather than heat-sealed, and that’s a separate machine — the NF-60A-M.
Yes. We build to your U.S. supply at 60 Hz and confirm the voltage with your quote.
A kit of wear parts ships with your machine. Every part in the kit, and the lead time for anything outside it, is listed in your quote in writing.
Customers Also Interested In...
Send Us an Empty Tube and a Sample
Two things decide which machine you need: whether your tubes are plastic, laminated or aluminum, because each is sealed differently, and how many you need a day. Tell us both and we’ll tell you whether a semi-automatic machine is enough.
Better still, send us a few empty tubes and a sample of your product. We’ll fill and seal them and send them back.
Direct from our factory
Lead time confirmed in your quote
Installation and training available
Spare parts listed in your quote